Remove wheel tester.

Merge mouse wheel logic.

CHANGELOG.txt

@@ -1,3 +1,9 @@
+Quisk Version 4.2.55  October 2026
+==================================
+Karl Heinz, K5KHK, provided a patche to fix the AC2YD remote control head. He provided another patch
+to fix Hamlib control when using WSJT-X improved. He added a mic jitter buffer to the remote control
+head so it works over WiFi. Thanks Karl!
+
 Quisk Version 4.2.54  August 2026
 =================================
 Quisk can now accept audio samples for Tx from TCI at rates 48000, 24000, 12000 and 8000. Please test.

README.md

@@ -0,0 +1,12 @@
+# Quisk Software Defined Radio
+
+Quisk is a software defined radio transceiver that runs on a PC or on a single board computer such as a Raspberry Pi.
+It is written in Python and C.
+It works with various kinds of radio hardware such as SoftRock, Hermes Lite 2,
+the SDR-IQ by RfSpace, and with network UDP samples.
+Quisk is easily extensible by writing your own hardware file in Python.
+
+I wrote Quisk back in 2008, and I have been maintaining it ever since.
+For questions and support, please visit the group https://groups.io/g/n2adr-sdr.
+
+For more information see https://james.ahlstrom.name/quisk.

__init__.py

@@ -1,2 +1,2 @@
-#Quisk version 4.2.54
+#Quisk version 4.2.55
 from .quisk import main

ac2yd/remote.c

@@ -53,6 +53,41 @@ static int control_head_data_width;					// app.data_width of control head for gr
 static int packets_sent;
 static int packets_recd;
 
+///// The jitter buffer is thanks to Karl Heinz - K5KHK
+// Jitter buffer for the microphone samples received from the control head.  The network can hold
+// packets for 100 msec or more (Wi-Fi power saving and scanning) and then deliver them in a burst,
+// but the Hermes Tx buffer only has 50 msec of slack.  Without a buffer here, each late burst is an
+// underflow (a gap on the air) followed by an overflow (discarded samples).  So buffer mic_jb_target
+// frames before playing, and then release them at a steady MIC_JB_RATE.
+// The buffer adds its delay to the transmit audio, so it is off unless the configuration item
+// remote_radio_mic_jitter_ms is set.  When it is off, samples are passed on as they arrive.
+#define MIC_JB_RATE		8000	// frames per second sent by the control head
+#define MIC_JB_SIZE		8000	// ring buffer size in stereo frames
+#define MIC_JB_MAX_MS	500		// largest configurable delay; MIC_JB_SIZE must hold this plus MIC_JB_EXTRA
+#define MIC_JB_EXTRA	2000	// trim back to mic_jb_target above mic_jb_target + this (clock drift): 250 msec
+#define MIC_JB_IDLE		0.5		// seconds without packets that end a transmission
+
+static int16_t mic_jb[MIC_JB_SIZE * 2];
+static int mic_jb_target;	// frames to buffer before playing, from remote_radio_mic_jitter_ms; zero for off
+static int mic_jb_read, mic_jb_count, mic_jb_playing, mic_jb_starved;
+static int mic_jb_underruns, mic_jb_overruns;
+static double mic_jb_time, mic_jb_frac, mic_jb_last_packet;
+
+static void mic_jb_reset(void)
+{
+	int msec;
+
+	msec = QuiskGetConfigInt("remote_radio_mic_jitter_ms", 0);
+	if (msec < 0)
+		msec = 0;
+	else if (msec > MIC_JB_MAX_MS)
+		msec = MIC_JB_MAX_MS;
+	mic_jb_target = msec * MIC_JB_RATE / 1000;
+	mic_jb_read = mic_jb_count = mic_jb_playing = mic_jb_starved = 0;
+	mic_jb_underruns = mic_jb_overruns = 0;
+	mic_jb_frac = 0;
+}
+
 // Receive stereo 16-bit pcm radio speaker sound on the control head via UDP
 int read_remote_radio_sound_socket(complex double * cSamples)
 {
@@ -117,9 +152,9 @@ int read_remote_radio_sound_socket(complex double * cSamples)
 // Receive stereo 16-bit pcm microphone samples at the remote radio via UDP
 int read_remote_mic_sound_socket(complex double * cSamples)
 {
-	int i, bytes, nInt16, nSamples;
+	int i, j, bytes, nInt16, nSamples, nFrames;
 	int16_t buf[UDP_SEND_INT16];
-	double samp_r, samp_l;
+	double now, due;
 	struct timeval tm_wait;
 	fd_set fds;
 	static struct quisk_cHB45Filter HalfBand;
@@ -134,8 +169,8 @@ int read_remote_mic_sound_socket(complex double * cSamples)
 		quisk_filt_cInit(&cFiltInterp3, quiskAudio24p3Coefs, sizeof(quiskAudio24p3Coefs)/sizeof(double));
 	}
 
-	// read all available packets, one per loop
-	nSamples = 0;
+	// read all available packets into the jitter buffer, one per loop
+	now = QuiskTimeSec();
 	while (1) {
 		tm_wait.tv_sec = 0;
 		tm_wait.tv_usec = 0;
@@ -152,15 +187,71 @@ int read_remote_mic_sound_socket(complex double * cSamples)
 			break;
 		}
 		if (bytes > 0) {
+			if (mic_jb_starved) {	// the buffer ran dry; count it unless the transmission had ended
+				mic_jb_starved = 0;
+				if (now - mic_jb_last_packet < MIC_JB_IDLE)
+					mic_jb_underruns++;
+			}
+			mic_jb_last_packet = now;
 			nInt16 = bytes / 2;
-			for (i = 0; i < nInt16; i += 2) {
-				samp_r = buf[i];
-				samp_l = buf[i + 1];
-				cSamples[nSamples++] = (samp_r + I * samp_l) / CLIP16 * CLIP32;
+			for (i = 0; i + 1 < nInt16; i += 2) {
+				if (mic_jb_count >= MIC_JB_SIZE) {	// full: drop the oldest frame
+					mic_jb_read = (mic_jb_read + 1) % MIC_JB_SIZE;
+					mic_jb_count--;
+				}
+				j = (mic_jb_read + mic_jb_count) % MIC_JB_SIZE * 2;
+				mic_jb[j] = buf[i];
+				mic_jb[j + 1] = buf[i + 1];
+				mic_jb_count++;
 			}
 		}
 	} // while(1)
 
+	// release the frames that are due since the last call
+	nSamples = 0;
+	if (mic_jb_target == 0) {		// the jitter buffer is off: pass on everything received
+		nFrames = mic_jb_count;
+	}
+	else if ( ! mic_jb_playing) {
+		nFrames = 0;
+		if (mic_jb_count >= mic_jb_target) {
+			mic_jb_playing = 1;
+			mic_jb_time = now;
+			mic_jb_frac = 0;
+		}
+	}
+	else {
+		due = (now - mic_jb_time) * MIC_JB_RATE + mic_jb_frac;
+		if (due < 0)			// the clock was set back
+			due = 0;
+		else if (due > MIC_JB_RATE / 2)	// limit to 0.5 sec, well within SAMP_BUFFER_SIZE after interpolation
+			due = MIC_JB_RATE / 2;
+		mic_jb_time = now;
+		nFrames = (int)due;
+		mic_jb_frac = due - nFrames;
+		if (nFrames > mic_jb_count) {	// ran dry: play what is left, then buffer up again
+			nFrames = mic_jb_count;
+			mic_jb_playing = 0;
+			mic_jb_starved = 1;
+		}
+	}
+	for (i = 0; i < nFrames; i++) {
+		j = mic_jb_read * 2;
+		cSamples[nSamples++] = ((double)mic_jb[j] + I * (double)mic_jb[j + 1]) / CLIP16 * CLIP32;
+		mic_jb_read = (mic_jb_read + 1) % MIC_JB_SIZE;
+	}
+	mic_jb_count -= nFrames;
+	if (mic_jb_target && mic_jb_count > mic_jb_target + MIC_JB_EXTRA) {	// the control head's clock is faster than ours
+		i = mic_jb_count - mic_jb_target;
+		mic_jb_read = (mic_jb_read + i) % MIC_JB_SIZE;
+		mic_jb_count -= i;
+		mic_jb_overruns++;
+	}
+	if ((mic_jb_underruns || mic_jb_overruns) && now - mic_jb_last_packet > MIC_JB_IDLE) {
+		QuiskPrintf("Remote mic jitter buffer: %d underruns, %d overruns\n", mic_jb_underruns, mic_jb_overruns);
+		mic_jb_underruns = mic_jb_overruns = 0;
+	}
+
 	nSamples = quisk_cInterpolate(cSamples, nSamples, &cFiltInterp3, 3);
 	nSamples = quisk_cInterp2HB45(cSamples, nSamples, &HalfBand);
 
@@ -716,6 +807,7 @@ PyObject * quisk_start_remote_radio_remote_sound(PyObject * self, PyObject * arg
 
 	packets_sent = 0;
 	packets_recd = 0;
+	mic_jb_reset();
 
 	return Py_None;
 }
@@ -742,6 +834,7 @@ PyObject * quisk_stop_remote_radio_remote_sound(PyObject * self, PyObject * args
 	control_head_graph_socket_started = 0;
 	remote_radio_graph_socket_started = 0;
 	control_head_data_width = 0;
+	mic_jb_reset();
 
 	QuiskPrintf("total packets sent = %i, recd = %i\n", packets_sent, packets_recd);
 

ac2yd/remote_common.py

@@ -190,10 +190,20 @@ class Remot:	# Remote comtrol base class
       return
     try:	# Read any data from the socket
       text = self.remote_ctl_connection.recv(1024)
-    except:
-      #traceback.print_exc()
+      # Thanks to Karl Heinz - K5KHK
+    except (BlockingIOError, InterruptedError, socket.timeout): # No data available now
+      return
+    except OSError: # For example ConnectionResetError: the Control Head is gone
+      print('Closing Remote Control connection: recv() failed')
+      self.RemoteCtlClose(False)
       return
     else:					# We got some characters
+      if not text: # recv() returns nothing only when the Control Head has closed the connection
+        # Close now rather than waiting for the heartbeat timeout: a Control Head that
+        # crashed or lost its network may have left the transmitter keyed.
+        print('Closing Remote Control connection: closed by Control Head')
+        self.RemoteCtlClose(False)
+        return
       if not isinstance(text, str):
         text = text.decode('utf-8')
       self.received += text
@@ -375,13 +385,22 @@ class Remot:	# Remote comtrol base class
           self.cw_next_keydown = None
 
   def StopTransmit(self):
-    # TODO:  Add code for modes other than CW
+    # PTT code added thanks to Karl Heinz - K5KHK
+    # Called whenever the remote session ends (RemoteCtlClose).  Release everything the
+    # Control Head may have keyed: the CW key and, for voice and digital modes, PTT.
+    # Without the PTT release, a Control Head that disappears while transmitting (a crash,
+    # a lost network, a dead battery) leaves the transmitter keyed until someone unkeys it
+    # at the radio.
     while len(self.cw_event_queue):
       self.cw_event_queue.popleft()
     self.cw_next_event_ts = None
     self.cw_next_keydown = None
     self.cw_key_down = 0
     QS.set_remote_cwkey(0)
+    ptt = getattr(self.app, 'pttButton', None)
+    if ptt and ptt.GetValue():
+      print('Remote Control connection closed while transmitting: releasing PTT')
+      ptt.SetValue(0, True) # Same as releasing PTT at the radio; runs OnButtonPTT
 
   def ProcessRadioBtn(self, command, cmd_text):
     # Large and Small format screens send different button events for radio buttons.

afedrinet/afedrinet_io.c

@@ -128,10 +128,10 @@ static PyObject * open_rx_udp(const char * ip, int port)
 			shutdown(rx_udp_socket, QUISK_SHUT_BOTH);
 			close(rx_udp_socket);
 			rx_udp_socket = INVALID_SOCKET;
-			sprintf(buf, "Failed to connect to UDP %s port %u", ip, port);
+			snprintf(buf, sizeof(buf), "Failed to connect to UDP %s port %u", ip, port);
 		}
 		else {
-			sprintf(buf, "Capture from UDP %s port %u", ip, port);
+			snprintf(buf, sizeof(buf), "Capture from UDP %s port %u", ip, port);
 #if DEBUG_IO
 			if (getsockopt(rx_udp_socket, SOL_SOCKET, SO_RCVBUF, (char *)&intbuf, &bufsize) == 0)
 			{

configure.py

@@ -727,17 +727,6 @@ class Configuration:
         count -= 1
     return count
 
-class xxConfigHelp(wx.html.HtmlWindow):	# The "Help with Radios" first-level page
-  """Create the help screen for the configuration tabs."""
-  def __init__(self, parent):
-    wx.html.HtmlWindow.__init__(self, parent, -1, size=(win_width, 100))
-    if "gtk2" in wx.PlatformInfo:
-      self.SetStandardFonts()
-    self.SetFonts("", "", [10, 12, 14, 16, 18, 20, 22])
-    self.SetBackgroundColour(parent.bg_color)
-    # read in text from file help_conf.html in the directory of this module
-    self.LoadFile('help_conf.html')
-
 class QPowerMeterCalibration(wx.Frame):
   """Create a window to enter the power output and corresponding ADC value AIN1/2"""
   def __init__(self, parent, local_names):
@@ -2302,7 +2291,8 @@ class ControlMixin:
         if name in ('hot_key_ptt_toggle', 'hot_key_ptt_if_hidden', 'keyupDelay', 'cwTone', 'pulse_audio_verbose_output',
                     'start_cw_delay', 'start_ssb_delay', 'maximum_tx_secs', 'quisk_serial_cts', 'quisk_serial_dsr',
                     'hot_key_ptt1', 'hot_key_ptt2', 'midi_ptt_toggle', 'TxRxSilenceMsec',
-                    'fixed_tune_offset', 'calibrate_temp_20', 'calibrate_temp_40', 'calibrate_current_0', 'calibrate_current_1'):
+                    'fixed_tune_offset', 'calibrate_temp_20', 'calibrate_temp_40', 'calibrate_current_0', 'calibrate_current_1',
+                    'remote_radio_mic_jitter_ms'):
           setattr(conf, name, x)
           application.ImmediateChange(name)
         elif name[0:4] in ('lin_', 'win_'):

docs.html

@@ -307,6 +307,7 @@ These are part of your operating system. You only install them once unless it ch
 </p>
 <br>
 <pre>
+sudo apt-get install gcc
 sudo apt-get install libfftw3-dev
 sudo apt-get install libasound2-dev
 sudo apt-get install portaudio19-dev

makefile

@@ -56,7 +56,7 @@ $(OBJDIR):
 	@mkdir -p $(OBJDIR)
 
 # Link the shared library object
-$(TARGET): $(OBJS)
+$(TARGET): $(OBJS) ac2yd/remote.o
 	$(CC) -o $@ $(OBJS) ac2yd/remote.o $(LDFLAGS)
 
 # Define the location for dependency files

pyproject.toml

@@ -4,7 +4,7 @@ build-backend = "setuptools.build_meta"
 
 [project]
 name = "quisk"
-version = "4.2.54"
+version = "4.2.55"
 requires-python = ">=3.13"
 description = 'QUISK is a Software Defined Radio (SDR) transceiver that can control various radio hardware.'
 license = "GPL-2.0-or-later"

quisk.c

@@ -4830,7 +4830,7 @@ static PyObject * set_multirx_mode(PyObject * self, PyObject * args)
 
 	if (!PyArg_ParseTuple (args, "ii", &index, &mode))
 		return NULL;
-	if (index < QUISK_MAX_SUB_RECEIVERS)
+	if (index >= 0 && index < QUISK_MAX_SUB_RECEIVERS)
 		multirx_mode[index] = mode;
 	Py_INCREF (Py_None);
 	return Py_None;
@@ -4842,7 +4842,7 @@ static PyObject * set_multirx_freq(PyObject * self, PyObject * args)
 
 	if (!PyArg_ParseTuple (args, "ii", &index, &freq))
 		return NULL;
-	if (index < QUISK_MAX_SUB_RECEIVERS)
+	if (index >= 0 && index < QUISK_MAX_SUB_RECEIVERS)
 		multirx_freq[index] = freq;
 	Py_INCREF (Py_None);
 	return Py_None;
@@ -4860,7 +4860,7 @@ static PyObject * set_multirx_play_channel(PyObject * self, PyObject * args)
 {
 	if (!PyArg_ParseTuple (args, "i", &multirx_play_channel))
 		return NULL;
-	if (multirx_play_channel >= QUISK_MAX_SUB_RECEIVERS)
+	if (multirx_play_channel < 0 || multirx_play_channel >= QUISK_MAX_SUB_RECEIVERS)
 		multirx_play_channel = -1;
 	Py_INCREF (Py_None);
 	return Py_None;
@@ -5638,6 +5638,10 @@ static void measure_freq(complex double * cSamples, int nSamples, int srate)
 			ipeak = i;
 		}
 	}
+	if (ipeak < 1)
+		ipeak = 1;
+	else if (ipeak > fft_size - 2)
+		ipeak = fft_size - 2;
 	c3 = 1.36 * (fft_average[ipeak+1] - fft_average[ipeak - 1]) / (fft_average[ipeak-1] + fft_average[ipeak] + fft_average[ipeak+1]);
 	freq = srate * (2 * (ipeak + c3) - fft_size) / 2 / fft_size;
 	freq += rx_tune_freq;
@@ -6006,6 +6010,8 @@ static PyObject * record_app(PyObject * self, PyObject * args)
 	}
 	// Initialize plan for multirx FFT
 	multirx_fft_width = multirx_data_width * MULTIRX_FFT_MULT;		// Use larger FFT than graph size
+	if (multirx_fft_next_samples)
+		free(multirx_fft_next_samples);
 	multirx_fft_next_samples = (fftw_complex *)malloc(multirx_fft_width * sizeof(fftw_complex));
 	multirx_fft_next_plan = quisk_create_or_cache_fftw_plan_dft_1d(multirx_fft_width, multirx_fft_next_samples, multirx_fft_next_samples, FFTW_FORWARD, FFTW_MEASURE);
 	if (current_graph)

quisk.py

@@ -39,6 +39,7 @@ from filters import Filters
 import dxcluster
 import configure
 import quisk_conf_defaults as conf
+import quisk_utils
 import quisk_wdsp
 
 for name in configure.name2format:      # Add defaults. These may be overwritten by a user config file.
@@ -742,6 +743,7 @@ class HamlibHandlerRig2:	# Test with telnet localhost 4532
     self.vfo = "Main"
     self.split_mode = 0
     self.split_vfo = 'VFO'
+    self.lock_mode = 0
     h = self.Handlers = {}
     h[''] = self.ErrProtocol
     h['dump_state']	= self.DumpState
@@ -765,6 +767,8 @@ class HamlibHandlerRig2:	# Test with telnet localhost 4532
     h['set_split_freq']	= self.SetSplitFreq
     h['get_split_vfo']	= self.GetSplitVfo
     h['set_split_vfo']	= self.SetSplitVfo
+    h['get_lock_mode']	= self.GetLockMode
+    h['set_lock_mode']	= self.SetLockMode
     self.MakeDumpState()
   def MakeDumpState(self):
     dump_state = []
@@ -1009,7 +1013,8 @@ class HamlibHandlerRig2:	# Test with telnet localhost 4532
       self.ErrParam()
     else:
       freq = int(freq + 0.5)
-      self.app.ChangeRxTxFrequency(freq, None)
+      # Like a real radio, keep the mode. Hamlib caches the mode, so the client would not notice a mode change.
+      self.app.ChangeRxTxFrequency(freq, None, keep_mode=True)
   def GetSplitFreq(self):	# The Tx Frequency
     self.Reply('TX Frequency', self.app.txFreq + self.app.VFO, 0)
   def SetSplitFreq(self):	# The Tx Frequency
@@ -1022,7 +1027,7 @@ class HamlibHandlerRig2:	# Test with telnet localhost 4532
     else:
       freq = int(freq + 0.5)
       # This always controls the Tx frequency
-      self.app.ChangeRxTxFrequency(None, freq)
+      self.app.ChangeRxTxFrequency(None, freq, keep_mode=True)
   def GetSplitVfo(self):
     self.Reply('Split', self.split_mode, 'TX VFO', self.split_vfo, 0)
   def SetSplitVfo(self):
@@ -1107,6 +1112,22 @@ class HamlibHandlerRig2:	# Test with telnet localhost 4532
         Lab = label
         diff = df
     self.app.filterButns.SetLabel(Lab, True)
+  # The code for the lock_mode and keep_mode was supplied by Karl Heinz - K5KHK. Thanks Karl!
+  def GetLockMode(self):
+    # Hamlib netrigctl always reads two lines, so an error reply "RPRT -4" makes it wait for its 10 second timeout.
+    # Reply like rigctld with the lock value and then "RPRT 0".
+    if self.extended:
+      self.Reply('Locked', self.lock_mode, 0)
+    else:
+      self.Send("%d\nRPRT 0\n" % self.lock_mode)
+  def SetLockMode(self):
+    lock = self.GetParamNumber()
+    try:
+      self.lock_mode = int(lock)
+    except:
+      self.ErrParam()
+    else:
+      self.Reply(0)
   def GetVfo(self):
     self.Reply('VFO', self.vfo, 0)
   def SetVfo(self):
@@ -2564,7 +2585,7 @@ class GraphScreen(wx.Window):
     else:
       self.mouse_is_rx = False
     if self.mouse_is_rx:
-      freq = application.rxFreq + self.VFO + wm * event.GetWheelRotation() // event.GetWheelDelta()
+      freq = application.rxFreq + self.VFO + quisk_utils.wheel_step(event.GetWheelRotation(), event.GetWheelDelta(), wm)
       if conf.freq_spacing:
         freq = self.FreqRound(freq, 0)
       elif freq >= 0:
@@ -2574,7 +2595,7 @@ class GraphScreen(wx.Window):
       tune = freq - self.VFO
       self.ChangeHwFrequency(self.txFreq, self.VFO, 'MouseWheel', event=event, rx_freq=tune)
     else:
-      freq = self.txFreq + self.VFO + wm * event.GetWheelRotation() // event.GetWheelDelta()
+      freq = self.txFreq + self.VFO + quisk_utils.wheel_step(event.GetWheelRotation(), event.GetWheelDelta(), wm)
       if conf.freq_spacing:
         freq = self.FreqRound(freq, 0)
       elif freq >= 0:
@@ -3642,8 +3663,8 @@ class HelpScreen(wx.html.HtmlWindow):
     if "gtk2" in wx.PlatformInfo:
       self.SetStandardFonts()
     self.SetFonts("", "", [10, 12, 14, 16, 18, 20, 22])
-    # read in text from file help.html in the directory of this module
-    self.LoadFile('help.html')
+    if not self.LoadFile('help.html'):
+      self.LoadFile('/usr/share/doc/quisk/help.html')
   def OnGraphData(self, data):
     pass
   def ChangeYscale(self, y_scale):
@@ -6136,7 +6157,7 @@ class App(wx.App):
       self.freqDisplay.Display(self.txFreq + self.VFO)
       self.fldigi_new_freq = self.txFreq + self.VFO
     return change
-  def ChangeRxTxFrequency(self, rx_freq=None, tx_freq=None):
+  def ChangeRxTxFrequency(self, rx_freq=None, tx_freq=None, keep_mode=False):
     if not self.split_rxtx and not tx_freq:
       tx_freq = rx_freq
     if tx_freq:
@@ -6147,7 +6168,7 @@ class App(wx.App):
       else:					# Change the VFO
         vfo = (tx_freq // 5000) * 5000 - 5000
         tune = tx_freq - vfo
-        self.BandFromFreq(tx_freq)
+        self.BandFromFreq(tx_freq, keep_mode)
       self.ChangeHwFrequency(tune, vfo, 'FreqEntry')
     if rx_freq and self.split_rxtx:		# Frequency must be on-screen
       tune = rx_freq - self.VFO
@@ -6337,7 +6358,8 @@ class App(wx.App):
       self.pttButton.Enable(False)
     else:
       self.pttButton.Enable(True)
-  def BandFromFreq(self, frequency):	# Change to a new band based on the frequency
+  def BandFromFreq(self, frequency, keep_mode=False):	# Change to a new band based on the frequency
+    # If keep_mode is True, do not change to the mode saved for the new band.
     if self.screen == self.bandscope_screen:
       return
     try:
@@ -6359,7 +6381,8 @@ class App(wx.App):
           vfo, tune, mode = self.bandState[band]
         except KeyError:
           vfo, tune, mode = (0, 0, 'LSB')
-        self.modeButns.SetLabel(mode, True)
+        if not keep_mode:
+          self.modeButns.SetLabel(mode, True)
         self.ChangeBand(band)
         break
   def ChangeBand(self, band):

quisk_conf_defaults.py

@@ -172,6 +172,22 @@ tx_level = {}
 # This is the maximum value of the slider.
 digital_tx_level = 100
 
+################ Receivers SuperPuper SDR, by UT3MK and US5NCJ 
+## hardware_file_name		Hardware file path, rfile
+# This is the file that contains the control logic for each radio.
+#hardware_file_name = 'ut3mkpkg/quisk_hardware.py'
+
+## widgets_file_name			Widget file path, rfile
+# This optional file adds additional controls for the radio.
+#widgets_file_name = ''
+
+## sdr1000_serial_port			Serial port, text
+# This is serial Port for the synthesizer, usually /dev/ttyUSBn on Linux or COMn on Win
+sdr1000_serial_port = "/dev/ttyUSB0"
+
+## sdr1000_serial_rate			Serial baud rate, integer
+# This is baud rate for the synthesizer.
+sdr1000_serial_rate = 57600
 
 
 ################ Receivers HiQSDR, The original N2ADR and HiQSDR radios.
@@ -425,7 +441,7 @@ hermes_PTT_hang_time = 4
 # This option only applies to the Hermes Lite 2. Set this to None if you don't have a tuner.
 # Set this to "Tune" to control the Icom AH-4 compatible ATU attached to the Hermes Lite 2 end plate.
 # Note that this option only applies to the HL2 end plate, not the IO board.
-# A tuner attached to the IO board is controlled from a button on the last line of the screen.
+# A tuner attached to the IO board is controlled from a button on the last line of the screen.
 # Then when the Spot button is pressed with a positive power, a tune request is sent to the ATU.
 # If the Spot button is pressed with a zero power level, the tuner is set to bypass mode.
 # Changes are immediate (no need to restart).
@@ -1508,6 +1524,19 @@ remote_radio_ip = ""
 # It is only necessary to enter it once on each computer.
 remote_radio_password = ""
 
+## remote_radio_mic_jitter_ms         Mic buffer msec for remote radio, integer
+# This is set on the remote radio, not the control head.  The network can hold the control
+# head's microphone packets for 100 msec or more and then deliver them in a burst, which is
+# common over Wi-Fi.  The transmit audio then has gaps.  This buffers the microphone audio
+# for the given time before transmitting it, so the bursts are smoothed out, at the cost
+# of that much more transmit delay.  Zero turns the buffer off, which is best on a wired
+# network.  If needed, try 150 msec.  The maximum is 500.  A change takes effect when the
+# next control head connects.
+remote_radio_mic_jitter_ms = 0
+#remote_radio_mic_jitter_ms = 100
+#remote_radio_mic_jitter_ms = 150
+#remote_radio_mic_jitter_ms = 250
+
 ## k4_tcp_ip			IP address for K4 TCP, text
 # This is the Quisk IP address for the TCP server implementing K4 commands.
 k4_tcp_ip = ""

quisk_utils.py

@@ -1,6 +1,29 @@
 from __future__ import print_function
 from __future__ import division
 
+
+def wheel_step(rotation, delta, step):
+  """Convert signed wheel rotation into configured frequency steps.
+
+  A measured downward event reported rotation=-180 with delta=120. Scaling
+  that by a 50 Hz step gives -75 Hz; flooring the resulting absolute frequency
+  made downward tuning jump -100 Hz while upward tuning moved only +50 Hz.
+  Round the wheel units symmetrically first: +/-180 now gives +/-50 Hz, while
+  +/-240 still gives +/-100 Hz rather than being collapsed to one step.
+  """
+  if delta == 0:
+    return 0
+  rotation = int(rotation)
+  delta = int(delta)
+  step = int(step)
+  direction = -1 if rotation * delta < 0 else 1
+  whole_steps, remainder = divmod(abs(rotation), abs(delta))
+  if remainder * 2 > abs(delta):
+    whole_steps += 1
+
+  return direction * whole_steps * step
+
+
 class SplineInterpolator:	# From Numerical Recipes in C
   """Interpolate a table of [x, y] values."""
   def __init__(self, table, Xmin=None, Xmax=None):

quisk_vna.py

@@ -26,6 +26,7 @@ import threading, webbrowser
 import _quisk as QS
 from quisk_widgets import *
 import configure
+import quisk_utils
 
 DEBUG = 0
 
@@ -630,7 +631,7 @@ class GraphScreen(wx.Window):
       mouse_x, mouse_y = self.GetMousePosition(event)
       self.SetTxFreq(index=mouse_x - self.originX)
   def OnWheel(self, event):
-    tune = self.display.tune_tx + event.GetWheelRotation() // event.GetWheelDelta()
+    tune = self.display.tune_tx + quisk_utils.wheel_step(event.GetWheelRotation(), event.GetWheelDelta(), 1)
     self.SetTxFreq(index=tune)
 
 class HelpScreen(wx.html.HtmlWindow):
@@ -640,8 +641,8 @@ class HelpScreen(wx.html.HtmlWindow):
     if "gtk2" in wx.PlatformInfo:
       self.SetStandardFonts()
     self.SetFonts("", "", [10, 12, 14, 16, 18, 20, 22])
-    # read in text from file help.html in the directory of this module
-    self.LoadFile('help_vna.html')
+    if not self.LoadFile('help_vna.html'):
+      self.LoadFile('/usr/share/doc/quisk/help_vna.html')
   def OnLinkClicked(self, link):
     webbrowser.open(link.GetHref(), new=2)
 

setup.py

@@ -82,7 +82,7 @@ N1MM+ and software that uses Hamlib.
 		'quisk.hermes', 'quisk.hiqsdr', 'quisk.afedrinet', 'quisk.soapypkg',
 		'quisk.sdrmicronpkg', 'quisk.perseuspkg', 'quisk.ac2yd', 'quisk.multuspkg'],
 	package_dir =  {'quisk' : '.'},
-	package_data = {'' : ['*.txt', '*.html', '*.so', '*.dll'], 'quisk' : ['icons/*']},
+	package_data = {'' : ['*.txt', '*.html', '*.so', '*.dll'], 'quisk' : ['icons/*']},
 	entry_points = {'gui_scripts' : ['quisk = quisk.quisk:main', 'quisk_vna = quisk.quisk_vna:main']},
 	ext_modules = Modules,
 	provides = ['quisk'],

ut3mkpkg/README.txt

@@ -0,0 +1,2 @@
+This directory has files for the SDR-1000 clone synthesizer by
+UT3MK and US5NCJ

ut3mkpkg/__init__.py

@@ -0,0 +1 @@
+#

ut3mkpkg/quisk_hardware.py

@@ -0,0 +1,523 @@
+# -*- coding: utf-8 -*-
+
+
+from __future__ import print_function
+import serial, time, logging
+import re
+import _quisk as QS
+import quisk_conf_defaults as conf
+import sys, wx, traceback
+
+
+# ── ПОСЛЕДОВАТЕЛЬНЫЙ ПОРТ ДЛЯ CAT ───────────────────────────────────
+sdr1000_serial_port = "/dev/ttyUSB0"  # Windows: "COM3"  /  Linux: "/dev/ttyUSB0"
+sdr1000_serial_rate = 57600          # PowerSDR CAT: до 115200
+
+# ── ЛОГ ────────────────────────────────────────────────────────────
+logging.basicConfig(
+    level=logging.INFO,
+    format="%(asctime)s  %(levelname)-5s  %(message)s",
+    datefmt="%H:%M:%S",
+)
+log = logging.getLogger("SDR1000")
+
+Mode2Index = {'CWL':0, 'CWU':1, 'LSB':2, 'USB':3, 'AM':4,
+      'FM':5, 'EXT':6, 'DGT-U':7, 'DGT-L':8, 'DGT-IQ':9,
+      'IMD':10, 'FDV-U':11, 'FDV-L':12, 'DGT-FM':13}
+
+# ── КЛАСС УПРАВЛЕНИЯ ЖЕЛЕЗОМ ────────────────────────────────────────
+from quisk_hardware_model import Hardware as BaseHardware
+
+class Hardware(BaseHardware):
+    """
+    Quisk Hardware-класс для FlexRadio SDR-1000.
+    Использует CAT-команды протокола PowerSDR (ZZ + Kenwood).
+    """
+    # Буфер для приема данных с com-порта
+    serialbuf = '';
+
+    # Буфер для отправки команд на com-порт
+    cmdbuf = '';
+
+    # Буфер отправки IF
+    statusbuf ='';
+    statussending = False;
+
+    # Сопоставление размера шагов
+    STEP_MAP =  {
+        '1':   '0000', '10':  '0001', '50':  '1000', '100':  '0010',
+        '250': '1001', '500': '1010', '1k':  '0011', '5k':   '1011',
+        '9k':  '1100', '10k': '0100', '100k':'0101', '1M':   '0110',
+        '10M': '0111',
+    }
+
+    STEP_VAL = {
+        '1':    1,
+        '10':   10,
+        '50':   50,
+        '100':  100,
+        '250':  250,
+        '500':  500,
+        '1k':   1000,
+        '5k':   5000,
+        '9k':   9000,
+        '10k':  10000,
+        '100k': 100000,
+        '1M':   1000000,
+        '10M':  10000000,
+    }
+
+    # STEP_ENA = ['1', '10', '50', '100', '250', '500', '1k', '5k', '10k', '100k' ]
+    STEP_ENA = [ '10', '50', '100', '250', '500', '1k', '5k', '10k', '100k' ]
+
+    BAND_ENA = ['80', '40', '30', '20', '17', '15', '12', '10']
+
+    watchdog = 0
+    watchdog_limit = 100
+
+    # Сопоставление режимов Quisk → код MD (PowerSDR/Kenwood)
+    # TODO
+    
+    MODE_MAP = {
+        'LSB':  '1',  'USB':  '2',  'CWU':   '3',  'FM':  '4',
+        'AM':   '5',  'DGT-L':  '6',  'CWL':  '7',  
+        # Quisk-специфичные → стандартные
+        'DGT-U':'2', 'FMN':  '4',  'AMN': '5',
+        'DGT-FM':  '4',  'FDV-U':'2',  'FDV-L':'1',
+        'FSK' : '9', 'FSKR' : '2', 
+    }
+
+    def __init__(self, app, conf):
+        BaseHardware.__init__(self, app, conf)
+        self.ser = None
+        self.current_freq = 0
+        self.current_vfo = 0
+        self.current_mode = 'USB'
+        self.current_band = '80'
+        self.current_step = '50'
+        self.rf_gain_labels = ('RF -20', 'RF -10', 'RF 0', 'RF +10' )
+        self.current_pre = 0
+        self.current_ritfreq = 0
+        self.rit_active = False
+        self.ptt_active = False
+
+    # ── Открытие/закрытие ────────────────────────────────────────────
+
+    def open(self):
+        """Вызывается один раз при старте Quisk."""
+
+        try:
+            self.ser = serial.Serial(
+                sdr1000_serial_port,
+                sdr1000_serial_rate,
+                timeout=0, xonxoff=True,
+            )
+            log.debug("SDR-1000: COM-порт открыт %s @ %d",
+                     sdr1000_serial_port, sdr1000_serial_rate)
+        except serial.SerialException as e:
+            log.error("SDR-1000: не удалось открыть порт: %s", e)
+            self.ser = None
+            return "SDR-1000: ошибка порта %s" % sdr1000_serial_port
+
+        msg = "SDR-1000 подключен (%s, %s)" % (
+            sdr1000_serial_port, "PowerSDR")
+        return msg
+
+    def close(self):
+        """Вызывается один раз при завершении Quisk."""
+        if self.ptt_active:
+            self.ser.cmdbuf += 'RX;'     # снять передачу
+
+        if self.ser and self.ser.is_open:
+            self.cmdbuf = ''
+            self.ser.flush
+            self.ser.close()
+            log.debug("SDR-1000: порт закрыт")
+
+    # ── Низкоуровневый CAT-обмен ────────────────────────────────────
+
+    def _cat(self):
+        """
+        Вызываться будет периодически для чтения порта
+        """
+        if not self.ser or not self.ser.is_open:
+            return ""
+
+        try:
+            #self.ser.write(frame)
+            if self.ser.in_waiting > 0:
+                sdata = self.ser.read(size=self.ser.in_waiting)
+                self.serialbuf += sdata.decode('ascii')
+            else:
+                self.watchdog += 1
+            if self.watchdog > self.watchdog_limit:
+                log.debug("Watchdog! Resetting arduino")
+                self.ser.dtr = 0
+                time.sleep(0.1)
+                self.ser.dtr = 1
+                self.ser.flush
+                self.ser.close()
+                time.sleep(0.1)
+                try:
+                    self.ser = serial.Serial(
+                    sdr1000_serial_port,
+                    sdr1000_serial_rate,
+                    timeout=0, xonxoff=True,
+                    )
+                    log.debug("SDR-1000: COM-порт открыт %s @ %d",
+                    sdr1000_serial_port, sdr1000_serial_rate)
+                except serial.SerialException as e:
+                    log.error("SDR-1000: не удалось открыть порт: %s", e)
+                    self.ser = None
+                    return "SDR-1000: ошибка порта %s" % sdr1000_serial_port
+                self.ser.flushInput()
+                self.ser.flushOutput()
+                self.watchdog = 0
+
+
+            ans = ''
+            while ';' in self.serialbuf:
+                cmds = self.serialbuf.partition(';')
+
+                cmd = cmds[0]
+                self.serialbuf = cmds[-1]
+                # log.info("Splitted to %s and %s", cmd, self.serialbuf)
+                if len(cmd) > 0:
+                    answer = ''
+                    cmddone = 0
+                    match cmd:
+                        case 'IF':
+                            # Запрос полного статуса
+                            # Возврат в statusbuf
+                            self.statusbuf = self.ReturnInfo()
+                            log.debug("Status refresh, buf: %s", self.serialbuf)
+                            cmddone = 1
+                        case 'ZZSM0':
+                            # Запрос показаний S-метра
+                            ans = self.ReturnSmeterA()
+                            log.debug("S-meter refresh, buf: %s", ans)
+                            cmddone = 1
+                        case 'PS1':
+                            # Включение
+                            ans = 'PS1;'
+                            log.debug("PowerON, buf: %s", ans)
+                            cmddone = 1
+                        case 'ZZPA':
+                            # Запрос показаний PRE ! TODO смена режима
+                            ans = self.ReturnPre()
+                            log.debug("PRE answer, buf: %s", ans)
+                            cmddone = 1
+                        case 'UP':
+                            # Запрос на увеличение частоты
+                            self.application.ChangeHwFrequency(9000,
+                                self.current_vfo+self.STEP_VAL[self.current_step])
+                            cmddone = 1
+                        case 'DN':
+                            # Запрос на уменьшение частоты
+                            self.application.ChangeHwFrequency(9000,
+                                self.current_vfo-self.STEP_VAL[self.current_step])
+                            cmddone = 1
+                        case 'ZZSU':
+                            # Запрос на увеличение шага
+                            self.StepInc()
+                            cmddone = 1
+                        case 'ZZSD':
+                            # Запрос на уменьшение шага
+                            self.StepDec()
+                            cmddone = 1
+                        case 'BU':
+                            # Запрос смены диапазона
+                            self.BandUp()
+                            cmddone = 1
+                        case 'BD':
+                            # Запрос смены диапазона
+                            self.BandDn()
+                            cmddone = 1
+                        case 'TX':
+                            # Transmit
+                            QS.set_PTT(1)
+                            self.ptt_active = True
+                            log.info("PTT ON")
+                            cmddone = 1
+                        case 'RX':
+                            # Recieve
+                            QS.set_PTT(0)
+                            self.ptt_active = False
+                            log.info("PTT OFF")
+                            cmddone = 1
+                            
+                        case 'ZZQR':
+                            # Запрос восстановление QuickSave
+                            cmddone = 1
+
+                    if len(cmd) > 4 and not cmddone:
+                        log.debug("Try to match cmd: %s, buf: %s", cmd[0:4], self.serialbuf)
+                        match cmd[0:4]:
+                            case 'ZZPA':
+                                # Запрос изменения PRE
+                                self.SetPre(cmd)
+                                ans = self.ReturnPre()
+                                log.debug("PRE set, buf: %s", ans)
+                                cmddone = 1
+                            case 'ZZMD':
+                                # Запрос изменения режима
+                                self.SetMode(cmd)
+                                log.debug("Mode set, buf: %s", cmd)
+                                cmddone = 1
+                            case 'FA00':
+                                # Запрос изменения частоты
+                                self.SetFreq(cmd)
+                                log.debug("Freq set, buf: %s", cmd)
+                                cmddone = 1
+                    if not cmddone:
+                        log.info("unknown cmd: %s, buf: %s", cmd, self.serialbuf)
+                        ans = '?;'
+                    if len(ans) > 0:
+                        log.debug("Sending answer, buf: %s", ans)
+                        self.ser.write(ans.encode('ascii'))
+
+            if len(self.serialbuf) == 0:
+                if len(self.cmdbuf) > 0:
+                    cmds = self.cmdbuf.partition(';')
+                    cmd = cmds[0]
+                    self.cmdbuf = cmds[-1]
+                    log.debug("Sending cmd %s, buf: %s", cmd, self.cmdbuf)
+                    self.ser.write(cmd.encode('ascii'))
+            if (len(self.statusbuf) > 0) and not self.statussending:
+                self.statussending = True
+                log.debug("Sending status, buf: %s", self.statusbuf)
+                self.ser.write(self.statusbuf.encode('ascii'))
+                self.statusbuf = ''
+                self.statussending = False
+
+        # End of CAT
+        except Exception as e:
+            log.error("SDR-1000 CAT error: %s", e)
+            return ""
+
+    @staticmethod
+    def _fmt_freq(hz):
+        """Частота → 11 цифр: 14200000 → '00014200000'."""
+        return "%011d" % int(hz)
+
+    # ── Quisk API: частота ──────────────────────────────────────────
+
+    def ChangeFrequency(self, tune, vfo, source='', band='', event=None):
+        """Quisk вызывает при смене частоты. Возвращает (tune, vfo)."""
+        if tune and tune != self.current_freq:
+            self.current_freq = tune
+            self.current_vfo = tune-9000
+            if re.search('FA\\d{11};', self.cmdbuf,0):
+                log.debug("--> RE MATCH")
+                re.sub('FA\\d{11};', "FA" + self._fmt_freq(tune)+";", self.cmdbuf, 1)
+            # self.cmdbuf += ("FA" + self._fmt_freq(tune)+";")
+            else:
+                self.cmdbuf += ("FA" + self._fmt_freq(tune)+";")
+            log.debug("VFO A → %d Hz (%.6f MHz)", self.current_vfo, self.current_freq / 1e6)
+        return self.current_freq, self.current_vfo
+
+    def ReturnInfo(self):
+        ritstr = self.application.ritFreq
+        if ritstr >= 0:
+            ritsign = "+"
+        else:
+            ritsign = ""
+        answer = "IF%011d%4s%s%05d%01d0000%01d%1s0000000;" % (
+            self.current_freq, self.STEP_MAP[self.current_step],
+            ritsign,ritstr,self.application.ritButton.GetValue(),
+            self.ptt_active,self.MODE_MAP[self.current_mode])
+        # log.info(answer)
+        return answer
+
+    def ReturnSmeterA(self):
+        i = round((self.application.smeter_db + 67) * 2)
+        if i < 0:
+            i = 0
+        elif i > 260:
+            i = 260
+        answer = "ZZSM0%03d;" % ( i )
+        # log.info(answer)
+        return answer
+
+    def ReturnPre(self):
+        answer = "ZZPA%01d;" % ( self.current_pre )
+        return answer
+
+    def SetPre(self, precmd):
+        if len(precmd) == 5:
+            match precmd:
+                case 'ZZPA0': i = 0
+                case 'ZZPA1': i = 1
+                case 'ZZPA2': i = 2
+                case 'ZZPA3': i = 3
+                case _: i = 0
+            self.current_pre = i
+
+    def SetFreq(self, freqcmd):
+        if len(freqcmd) == 13:
+            newfreq = int(freqcmd[2:])
+            log.info("Request to change freq: %d", newfreq)
+            self.current_vfo=newfreq-9000
+            self.application.ChangeHwFrequency(9000, self.current_vfo)
+    
+    def OnButtonRfGain(self, event):
+        btn = event.GetEventObject()
+        n = btn.index
+        self.current_pre = n
+        self.cmdbuf += ("ZZPA%1d;" % self.current_pre)
+        
+    def SetMode(self, modecmd):
+        if len(modecmd) == 6:
+            log.info("Request to change mode: %s", modecmd[4:])
+            match modecmd[4:]:
+                
+                # 00 = LSB  =>  LSB
+                # 01 = USB  =>  USB
+                # 02 = DSB  =>  USB
+                # 03 = CWL  =>  CW
+                # 04 = CWU  =>  CW
+                # 05 = FMN  =>  FMN
+                # 06 = AM   =>  AM
+                # 07 = DIGU =>  FSKR
+                # 08 = SPEC =>  AMN
+                # 09 = DIGL =>  FSK
+                # 10 = SAM  =>  USB
+                # 11 = DRM  =>  USB
+                
+                case '00': newmode = 'LSB'
+                case '01': newmode = 'USB'
+                case '02': newmode = 'USB'
+                case '03': newmode = 'CWL'
+                case '04': newmode = 'CWU'
+                case '05': newmode = 'FM'
+                case '06': newmode = 'AM'
+                case '07': newmode = 'DGT-U'
+                case '08': newmode = 'AM'
+                case '09': newmode = 'DGT-L'
+                case '10': newmode = 'USB'
+                case '11': newmode = 'USB'
+                case _: newmode = 'USB'
+            self.current_mode = newmode
+            self.application.mode = self.current_mode
+            self.application.MakeFilterButtons(self.application.Mode2Filters(self.current_mode))
+            QS.set_rx_mode(Mode2Index.get(self.current_mode, 3))
+            if self.current_mode == 'CWL':
+                self.application.SetRit(conf.cwTone)
+            elif self.current_mode == 'CWU':
+                self.application.SetRit(-conf.cwTone)
+            else:
+                self.application.SetRit(0)
+            if self.current_mode in ('CWL', 'CWU'):
+                self.application.SetFilterByMode('CW')
+            elif self.current_mode in ('LSB', 'USB'):
+                self.application.SetFilterByMode('SSB')
+            elif self.current_mode == 'AM':
+                self.application.SetFilterByMode('AM')
+            elif self.current_mode[0:2] == 'FM':
+                self.application.SetFilterByMode('FM')
+            elif self.current_mode[0:4] == 'DGT-':
+                self.application.SetFilterByMode('DGT')
+            self.application.sliderSquelch.DeleteSliderWindow()
+            
+            if self.current_mode == 'FM':
+                self.application.sliderSquelch.SetSlider(self.application.levelSquelch)
+            else:
+                self.application.sliderSquelch.SetSlider(self.application.levelSquelchSSB)
+            self.application.OnBtnSquelch()
+            if self.current_mode not in ('FDV-L', 'FDV-U'):
+                self.application.graph.SetDisplayMsg()
+                self.application.waterfall.SetDisplayMsg()
+            self.application.SetTxAudio()
+            
+    def StepInc(self):
+        i = self.STEP_ENA.index(self.current_step)
+        log.debug("Found index of %s, idx: %d", self.current_step, i)
+        if i < (len(self.STEP_ENA)-1):
+            self.current_step = self.STEP_ENA[i + 1]
+            log.debug("Step changed to %s, idx: %d", self.current_step, i+1)
+        else: 
+            log.debug("Step not changed, remain %s", self.current_step)
+
+
+    def StepDec(self):
+        i = self.STEP_ENA.index(self.current_step)
+        log.info("Found index of %s, idx: %d", self.current_step, i)
+        if i > 0:
+            self.current_step = self.STEP_ENA[i - 1]
+            log.debug("Step changed to %s, idx: %d", self.current_step, i-1)
+        else: 
+            log.debug("Step not changed, remain %s", self.current_step)
+
+    def BandUp(self):
+        i = self.BAND_ENA.index(self.current_band)
+        log.debug("Found index of %s, idx: %d", self.current_band, i)
+        if i < (len(self.BAND_ENA)-1):
+            self.current_band = self.BAND_ENA[i + 1]
+        else:
+            self.current_band = self.BAND_ENA[0]
+        log.info("Band changed to %s, idx: %d", self.current_band, i)
+        vfo, tune, mode = self.application.bandState[self.current_band]
+        self.application.ChangeHwFrequency(9000, vfo+tune)
+
+    def BandDn(self):
+        i = self.BAND_ENA.index(self.current_band)
+        log.debug("Found index of %s, idx: %d", self.current_band, i)
+        if i > 0:
+            self.current_band = self.BAND_ENA[i - 1]
+        else:
+            self.current_band = self.BAND_ENA[len(self.BAND_ENA)-1]
+        log.info("Band changed to %s, idx: %d", self.current_band, i)
+        vfo, tune, mode = self.application.bandState[self.current_band]
+        self.application.ChangeHwFrequency(9000, vfo+tune)
+
+    def ReturnFrequency(self):
+        """Опрос ~10 Гц. Возвращает (tune, vfo) или (None, None)."""
+        # SDR-1000 не сообщает частоту сам, поэтому возвращаем None
+        return None, None
+
+    # ── Quisk API: режим ─────────────────────────────────────────────
+
+    def ChangeMode(self, mode):
+        """Quisk вызывает при смене режима. mode: 'USB', 'CW', и т.д."""
+        # Нормализуем DGT-* → USB
+        # if mode.startswith('DGT'):
+        #     mode = 'USB'
+        code = self.MODE_MAP.get(mode)
+        if not code:
+            log.warning("Неизвестный режим Quisk: %s → по умолчанию USB", mode)
+            code = '2'
+        self.cmdbuf += ("MD" + code+';')
+        self.current_mode = mode
+        log.debug("Режим → %s (MD%s)", mode, code)
+
+    # ── Quisk API: диапазон ─────────────────────────────────────────
+
+    def ChangeBand(self, band):
+        """Quisk вызывает при смене диапазона. band: '160', '80', …"""
+        BaseHardware.ChangeBand(self, band)
+        log.info("Диапазон → %s м", band)
+
+    # ── Quisk API: PTT ──────────────────────────────────────────────
+
+    def OnButtonPTT(self, event=None):
+        """Quisk вызывает при нажатии/отпускании PTT."""
+        if event:
+            self.ptt_active = bool(event.GetEventObject().GetValue())
+        #self._cat("ZZTX%d" % (1 if self.ptt_active else 0))
+        log.debug("PTT %s", "ON" if self.ptt_active else "OFF")
+
+    # ── Quisk API: HeartBeat (~10 Гц) ───────────────────────────────
+
+    def HeartBeat(self):
+        """Периодический опрос — можно использовать для синхронизации."""
+        self._cat()
+
+    def FastHeartBeat(self):    # Called frequently by the GUI thread
+        pass
+
+    # ── Quisk API: TUNE ─────────────────────────────────────────────
+
+    def OnBtnFDX(self, is_fdx):
+        """Кнопка FDX (полный дуплекс)."""
+        log.debug("FDX → %s", is_fdx)
+