Quisk version 4.2.49

CHANGELOG.txt

@@ -1,3 +1,47 @@
+Quisk Version 4.2.49  December 2025
+===================================
+This version adds more features for the Anan 10E and other OpenHPSDR radios. Please test.
+
+I added the forward power, SWR, temperature and PA current display to the OpenHPSDR radio. But
+I don't have that radio so I need some help. I think the forward and reverse power connections
+are correct, but it is still necessary to create a table to convert analog input codes to power.
+Go to the Hardware screen and check the "Power meter calibration" setting. You will need to enter
+"New" and create a suitable table. To see the ADC values, choose table "Show ADC".
+
+There is no protocol standard to specify which analog input is used for temperature and PA current.
+And AFAIK the Anan 10E has no such sensors. I am hoping to use the board ID to find the right input.
+The ADC conversion is linear and the two points are specified on the Hardware screen.
+
+I currently assigned the analog inputs as follows:
+AIN1	Forward power
+AIN2	Reverse power
+AIN3	PA current
+AIN5	Temperature
+If you need to see the ADC codes 0-4095 for each input, go to hermes/quisk_hardware.py and
+change DEBUG_SENSORS to one.
+
+Quisk Version 4.2.48  November 2025
+===================================
+This is a quisk fix for a bug in the new OpenHPSDR radios. It fixes use_rx_udp that was reset to zero.
+
+Quisk Version 4.2.47  November 2025
+===================================
+To improve the performance of Quisk with the Anan 10-E and other OpenHPSDR radios, I added
+a new type of radio "OpenHPSDR". Use this type for the Anan 10-E and similar radios. It removes
+all the protocol extensions added by the Hermes-Lite2 project.  I removed the configuration
+option "Hermes Lite2 protocol enable". This is now automatic.
+
+I added buttons for antennas 0, 1, 2 and 3 for OpenHPSDR radios that support more antennas.
+I added controls for the OpenHPSDR preamplifier and attenuator.
+
+I do not have any Apache Labs radios, so I must depend on my users to report problems and solutions.
+
+Quisk Version 4.2.46  October 2025
+==================================
+I fixed a bug in Hamlib rig 2 which happens with the new Pure Signal code. The Hamlib "f" command
+now always returns the main receiver frequency, not one of the added receiver frequencies. This is
+consistent with the Flex ZZ commands.
+
 Quisk Version 4.2.45  October 2025
 ==================================
 The new FreeDV including RADE mode is now a built-in mode of Quisk. Just press "FDV" to talk FreeDV.

__init__.py

@@ -1,2 +1,2 @@
-#Quisk version 4.2.45
+#Quisk version 4.2.49
 from .quisk import main

configure.py

@@ -88,6 +88,7 @@ class Configuration:
       platform_ignore = 'win_'
     self.sections = []
     self.receiver_data = []
+    self.receiver_explain = []
     self.StatePath = conf.settings_file_path
     if not self.StatePath:
       self.StatePath = os.path.join(app.QuiskFilesDir, "quisk_settings.json")
@@ -158,9 +159,9 @@ class Configuration:
         dlg.Destroy()
     else:
       radio_dict["use_soapy"] = '0'
-    if radio_type not in ("HiQSDR", "Hermes", "Red Pitaya", "Odyssey", "Odyssey2"):
+    if radio_type not in ("HiQSDR", "Hermes", "Red Pitaya", "Odyssey", "Odyssey2", "OpenHPSDR"):
       radio_dict["use_rx_udp"] = '0'
-    if radio_type in ("Hermes", "Red Pitaya", "Odyssey2"):
+    if radio_type in ("Hermes", "Red Pitaya", "Odyssey2", "OpenHPSDR"):
       if "Hermes_BandDict" not in radio_dict:
         radio_dict["Hermes_BandDict"] = {}
       if "Hermes_BandDictTx" not in radio_dict:
@@ -601,6 +602,7 @@ class Configuration:
     # Receiver sections start with 16 #, "Receivers ", receiver name, explain
     # self.receiver_data is a list of [receiver_name, receiver_data]
     # receiver_data is a list of [data_name, text, fmt, help_text, values]
+    # self.receiver_explain is a list of the text in Receivers: the name, a comma and the explanation.
 
     # Variable names start with ## variable_name   variable_text, format
     #     The format is integer, number, text, boolean, integer choice, text choice, rfile
@@ -638,6 +640,7 @@ class Configuration:
         continue
       if line[0:27] == '################ Receivers ':
         section = 'Receivers'
+        self.receiver_explain.append(line[27:].strip())
         args = line[27:].split(',', 1)
         rxname = args[0].strip()
         section_data = []
@@ -2298,8 +2301,8 @@ class ControlMixin:
       if self.radio_name == Settings[1]:	# changed for current radio
         if name in ('hot_key_ptt_toggle', 'hot_key_ptt_if_hidden', 'keyupDelay', 'cwTone', 'pulse_audio_verbose_output',
                     'start_cw_delay', 'start_ssb_delay', 'maximum_tx_secs', 'quisk_serial_cts', 'quisk_serial_dsr',
-                    'hot_key_ptt1', 'hot_key_ptt2', 'midi_ptt_toggle', 'TxRxSilenceMsec', 'hermes_lite2_enable',
-                    'fixed_tune_offset'):
+                    'hot_key_ptt1', 'hot_key_ptt2', 'midi_ptt_toggle', 'TxRxSilenceMsec',
+                    'fixed_tune_offset', 'calibrate_temp_20', 'calibrate_temp_40', 'calibrate_current_0', 'calibrate_current_1'):
           setattr(conf, name, x)
           application.ImmediateChange(name)
         elif name[0:4] in ('lin_', 'win_'):
@@ -2400,6 +2403,7 @@ class BaseWindow(wx.ScrolledWindow, ControlMixin):
   def __init__(self, parent):
     wx.ScrolledWindow.__init__(self, parent)
     ControlMixin.__init__(self, parent)
+    self.SetScrollRate(8, 8)
 
 class ConfigConfig(BaseWindow):
   def __init__(self, parent, width):
@@ -2510,7 +2514,6 @@ The CW message will then repeat. A time of zero means no repeat.'
     sl, btn = self.AddTextSliderHelp(4, "    Repeat secs %.1f  ", 0, 0, 100, self.OnPlayFileRepeat, help_text, span=2, scale=0.1)
     self.NextRow()
     self.FitInside()
-    self.SetScrollRate(1, 1)
   def MakeFileButton(self, text, path, index, name, help_text):
     if index < 10:	# record buttons
       cb = self.AddCheckBox(4, text, self.OnCheckRecPlay)
@@ -2688,7 +2691,6 @@ class ConfigTxAudio(BaseWindow):
     application.CtrlTxAudioPreemph = sld
     self.NextRow()
     self.FitInside()
-    self.SetScrollRate(1, 1)
   def OnTimer(self, event):
     if not self.tmp_playing:
       self.timer.Stop()
@@ -2737,8 +2739,8 @@ class Radios(BaseWindow):	# The "Radios" first-level page
     self.NextRow()
     rb = self.AddRadioButton(1, "Add a new radio with the general type", self.NewTop)
     choices = []
-    for name, data in local_conf.receiver_data:
-      choices.append(name)
+    for explain in local_conf.receiver_explain:
+      choices.append(explain)
     choices.sort()
     self.add_type = self.AddComboCtrl(2, '', choices=choices, no_edit=True)
     self.add_type.SetSelection(0)
@@ -2766,7 +2768,6 @@ class Radios(BaseWindow):	# The "Radios" first-level page
     self.apply_btn = self.AddPushButton(3, "Apply", self.OnBtnApply)
     self.NewRadioNames()
     self.NewTop()
-    self.SetScrollRate(1, 1)
   def NewTop(self, event=None):
     if event:
       btn = event.GetEventObject()
@@ -2810,7 +2811,7 @@ class Radios(BaseWindow):	# The "Radios" first-level page
     if not name or self.DuplicateName(name):
       return
     self.add_name.SetValue('')
-    typ = self.add_type.GetValue().strip()
+    typ = self.add_type.GetValue().split(',')[0].strip()
     if local_conf.AddRadio(name, typ):
       self.NewRadioNames()
       local_conf.settings_changed = True
@@ -3003,7 +3004,6 @@ class RadioSection(BaseWindow):		# The pages for each section in the second-leve
       self.AddColSpacer(2, 20)
       self.AddColSpacer(5, 20)
     self.FitInside()
-    self.SetScrollRate(1, 1)
   def OnButtonChangeFavorites(self, event):
     if isinstance(event, (ChoiceCombo, ComboCtrl)):
       path = event.GetValue()
@@ -3128,7 +3128,6 @@ class RadioHardwareBase(BaseWindow):		# The Hardware page in the second-level no
     self.NextRow(7)
     self.AddColSpacer(2, 20)
     self.AddColSpacer(5, 20)
-    self.SetScrollRate(1, 1)
   def OnButtonChangeHardware(self, event):
     if isinstance(event, (ChoiceCombo, ComboCtrl)):
       path = event.GetValue()
@@ -3175,25 +3174,24 @@ class RadioHardware(RadioHardwareBase):		# The Hardware page in the second-level
     data_names = local_conf.GetReceiverData(radio_type)
     col = 1
     border = 2
-    hermes_board_id = 0
-    if radio_type == "Hermes":
-      try:
-        hermes_board_id = application.Hardware.hermes_board_id
-      except:
-        pass
+    try:
+      is_HermesLite2 = application.Hardware.is_HermesLite2
+    except:
+      is_HermesLite2 = False
     if radio_name == Settings[1] and hasattr(application.Hardware, "ProgramGateware"):
       help_text = "Choose an RBF file and program the Gateware (FPGA software) over Ethernet."
       self.AddTextButtonHelp(1, "Gateware Update", "Program from RBF file..", application.Hardware.ProgramGateware, help_text)
       col = 1
       self.NextRow(self.row + 2)
     for name, text, fmt, help_text, values in data_names:
+      text = text.replace("\\u2103", "\u2103")
       if name in ('hardware_file_name', 'widgets_file_name'):
         pass
       elif name[0:4] == platform_ignore:
         pass
       elif name in ('Hermes_BandDictEnTx', ):
         pass
-      elif 'Hl2_' in name and hermes_board_id != 6:
+      elif 'Hl2_' in name and not is_HermesLite2:
         pass
       elif fmt[0:4] in ('dict', 'list'):
         pass
@@ -3222,7 +3220,7 @@ class RadioHardware(RadioHardwareBase):		# The Hardware page in the second-level
           col = 1
           border = 2
           self.NextRow()
-    if hermes_board_id == 6:
+    if is_HermesLite2:
       if col == 4:
         self.NextRow()
       help_text = ('This controls the bias level for transistors in the final power amplifier.  Enter a level from 0 to 255.'
@@ -3238,7 +3236,6 @@ class RadioHardware(RadioHardwareBase):		# The Hardware page in the second-level
       self.HermesWriteBiasButton = self.AddPushButton(7, "Write", self.OnButtonHermesWriteBias, border=0)
       self.HermesWriteBiasButton.Enable(enbl)
     self.FitInside()
-    self.SetScrollRate(1, 1)
   def OnHermesChangeBias0(self, event):
     value = self.HermesBias0.GetValue()
     application.Hardware.ChangeBias0(value)
@@ -3852,7 +3849,6 @@ class RadioSound(BaseWindow):		# The Sound page in the second-level notebook for
         break
     self.gbs = gbs
     self.FitInside()
-    self.SetScrollRate(1, 1)
   def ItemValue(self, row, col):
     data_name = self.sound_names[row][col]
     if col == 4:		# Device names
@@ -4080,7 +4076,6 @@ The Tx bits are sent as the "Alex" filters and are sent to the J16 interface.'
         self.AddBitField(col + 1, 7, 'Hermes_BandDictTx', band, bus, self.ChangeIO)
         self.NextRow()
     self.FitInside()
-    self.SetScrollRate(1, 1)
   def SortCmp(self, item1):
     # Numerical conversion of band name to  megahertz
     try:
@@ -4255,7 +4250,6 @@ class RadioRemote(BaseWindow):		# The Remote page in the second-level notebook f
     self.AddColSpacer(3, 20)
     self.AddColSpacer(6, 20)
     self.FitInside()
-    self.SetScrollRate(1, 1)
   def OnChangePassword(self, event):
     text = local_conf.globals.get('remote_radio_password', '')
     dlg = wx.TextEntryDialog(self, "Please enter a password for remote access",
@@ -4337,7 +4331,6 @@ class xxRadioFilters(BaseWindow):		# The Filters page in the second-level notebo
       self.NextRow()
       index += 1
     self.FitInside()
-    self.SetScrollRate(1, 1)
   def OnChangeFreq(self, event):
     freq = event.GetString()
     radio_dict = local_conf.GetRadioDict(self.radio_name)

hermes/hpsdr_widgets.py

@@ -0,0 +1,157 @@
+# Please do not change this widgets module for Quisk.  Instead copy
+# it to your own quisk_widgets.py and make changes there.
+#
+# This module is used to add extra widgets to the QUISK screen.
+
+import wx, math
+
+class BottomWidgets:	# Add extra widgets to the bottom of the screen
+  def __init__(self, app, hardware, conf, frame, gbs, vertBox):
+    self.config = conf
+    self.hardware = hardware
+    self.application = app
+    self.start_row = app.widget_row		# The first available row
+    self.start_col = app.button_start_col	# The start of the button columns
+    self.num_rows_added = 1
+    self.btnPreamp = app.QuiskCheckbutton(frame, self.OnBtnPreamp, text='Preamp')
+    gbs.Add(self.btnPreamp, (self.start_row, self.start_col), flag=wx.EXPAND)
+    bw, bh = self.btnPreamp.GetMinSize()
+    init = app.hermes_atten_dB
+    self.sliderAtten = app.SliderBoxHH(frame, 'Atten %d dB', init, 0, 31, self.OnAtten, True)
+    self.sliderAtten.idName = "RfAtten"
+    app.midiControls["RfAtten"]	= (self.sliderAtten, self.OnAtten)
+    hardware.ChangeAtten(init)
+    gbs.Add(self.sliderAtten, (self.start_row, self.start_col + 2), (1, 6), flag=wx.EXPAND)
+    if conf.button_layout == "Small screen":
+      # Display four data items in a single window
+      self.text_temperature = app.QuiskText1(frame, '', bh)
+      self.text_pa_current = app.QuiskText1(frame, '', bh)
+      self.text_fwd_power = app.QuiskText1(frame, '', bh)
+      self.text_swr = app.QuiskText1(frame, '', bh)
+      self.text_data = self.text_temperature
+      self.text_pa_current.Hide()
+      self.text_fwd_power.Hide()
+      self.text_swr.Hide()
+      b = app.QuiskPushbutton(frame, self.OnTextDataMenu, '..')
+      szr = self.data_sizer = wx.BoxSizer(wx.HORIZONTAL)
+      szr.Add(self.text_data, 1, flag=wx.ALIGN_CENTER_VERTICAL)
+      szr.Add(b, 0, flag=wx.ALIGN_CENTER_VERTICAL)
+      gbs.Add(szr, (self.start_row, self.start_col + 10), (1, 2), flag=wx.EXPAND)
+      # Make a popup menu for the data window
+      self.text_data_menu = wx.Menu()
+      item = self.text_data_menu.Append(-1, 'Temperature')
+      app.Bind(wx.EVT_MENU, self.OnDataTemperature, item)
+      item = self.text_data_menu.Append(-1, 'PA Current')
+      app.Bind(wx.EVT_MENU, self.OnDataPaCurrent, item)
+      item = self.text_data_menu.Append(-1, 'Fwd Power')
+      app.Bind(wx.EVT_MENU, self.OnDataFwdPower, item)
+      item = self.text_data_menu.Append(-1, 'SWR')
+      app.Bind(wx.EVT_MENU, self.OnDataSwr, item)
+    else:
+      szr = wx.BoxSizer(wx.HORIZONTAL)
+      gbs.Add(szr, (self.start_row, self.start_col + 10), (1, 18), flag=wx.EXPAND)
+      text_temperature = wx.StaticText(frame, -1, ' Temp 100DC XX', style=wx.ST_NO_AUTORESIZE)
+      size = text_temperature.GetBestSize()
+      text_temperature.Destroy()
+      self.text_temperature = wx.StaticText(frame, -1, '', size=size, style=wx.ST_NO_AUTORESIZE)
+      self.text_pa_current = wx.StaticText(frame, -1, '', size=size, style=wx.ST_NO_AUTORESIZE)
+      self.text_fwd_power = wx.StaticText(frame, -1, '', size=size, style=wx.ST_NO_AUTORESIZE)
+      self.text_swr = wx.StaticText(frame, -1, '', size=size, style=wx.ST_NO_AUTORESIZE)
+      flag=wx.ALIGN_LEFT|wx.ALIGN_CENTER_VERTICAL
+      szr.Add(self.text_temperature, 0, flag=flag)
+      szr.Add(self.text_pa_current, 0, flag=flag)
+      szr.Add(self.text_fwd_power, 0, flag=flag)
+      szr.Add(self.text_swr, 0, flag=flag)
+  def OnBtnPreamp(self, event):
+    self.hardware.ChangePreamp(self.btnPreamp.GetValue())
+  def OnAtten(self, event):
+    value = self.sliderAtten.GetValue()
+    self.hardware.ChangeAtten(value)
+    self.application.hermes_atten_dB = value
+  def Code2FwdRevWatts(self, fwd, rev):	# Convert the fwd/rev power code to watts forward and reverse
+    #print (self.hardware.hermes_rev_power, self.hardware.hermes_fwd_power)
+    fwd = self.hardware.InterpolatePower(fwd)
+    rev = self.hardware.InterpolatePower(rev)
+    # Which voltage is forward and reverse depends on the polarity of the current sense transformer
+    if fwd >= rev:
+      return fwd, rev
+    else:
+      return rev, fwd
+  def UpdateText(self):		# Called at intervals
+    conf = self.config
+    # Temperature
+    temp = self.hardware.hermes_temperature
+    if conf.calibrate_temp_20 == conf.calibrate_temp_40:
+      temp = " Temp ADC %4d" % temp
+    else:
+      m = 20.0 / (conf.calibrate_temp_40 - conf.calibrate_temp_20)
+      b = 20.0 - m * conf.calibrate_temp_20
+      temp = m * temp + b
+      temp = (" Temp %3.0f" % temp) + u'\u2103'
+    self.text_temperature.SetLabel(temp)
+    # power amp current
+    current = self.hardware.hermes_pa_current
+    if conf.calibrate_current_0 == conf.calibrate_current_1:
+      current = " Amps ADC %4d" % current
+    else:
+      m = 1.0 / (conf.calibrate_current_1 - conf.calibrate_current_0)
+      b = - m * conf.calibrate_current_0
+      current = m * current + b
+      current = " PA %4.0f ma" % (1000*current)
+    self.text_pa_current.SetLabel(current)
+    # forward and reverse peak power
+    if not self.hardware.power_interpolator:	# For no interpolator, show ADC
+      fwd = self.hardware.hermes_fwd_power
+      rev = self.hardware.hermes_rev_power
+      self.text_fwd_power.SetLabel("Fwd ADC %4d" % fwd)
+      self.text_swr.SetLabel("Rev ADC %4d" % rev)
+      return
+    fwd, rev = self.Code2FwdRevWatts(self.hardware.hermes_fwd_peak, self.hardware.hermes_rev_peak)
+    # forward less reverse power
+    power = fwd - rev
+    if power < 0.0:
+      power = 0.0
+    text = " PEP %3.1f watts" % power
+    self.text_fwd_power.SetLabel(text)
+    # SWR based on average power
+    fwd, rev = self.Code2FwdRevWatts(self.hardware.hermes_fwd_power, self.hardware.hermes_rev_power)
+    if fwd >= 0.05:
+      gamma = math.sqrt(rev / fwd)
+      if gamma < 0.98:
+        swr = (1.0 + gamma) / (1.0 - gamma)
+      else:
+        swr = 99.0
+      if swr < 9.95:
+        text = " SWR %4.2f" % swr
+      else:
+        text = " SWR %4.0f" % swr
+    else:
+      text = " SWR  ---"
+    self.text_swr.SetLabel(text)
+  def OnTextDataMenu(self, event):
+    btn = event.GetEventObject()
+    btn.PopupMenu(self.text_data_menu, (0,0))
+  def OnDataTemperature(self, event):
+    self.data_sizer.Replace(self.text_data, self.text_temperature)
+    self.text_data.Hide()
+    self.text_data = self.text_temperature
+    self.text_data.Show()
+    self.data_sizer.Layout()
+  def OnDataPaCurrent(self, event):
+    self.data_sizer.Replace(self.text_data, self.text_pa_current)
+    self.text_data.Hide()
+    self.text_data = self.text_pa_current
+    self.text_data.Show()
+    self.data_sizer.Layout()
+  def OnDataFwdPower(self, event):
+    self.data_sizer.Replace(self.text_data, self.text_fwd_power)
+    self.text_data.Hide()
+    self.text_data = self.text_fwd_power
+    self.text_data.Show()
+    self.data_sizer.Layout()
+  def OnDataSwr(self, event):
+    self.data_sizer.Replace(self.text_data, self.text_swr)
+    self.text_data.Hide()
+    self.text_data = self.text_swr
+    self.text_data.Show()
+    self.data_sizer.Layout()

hermes/quisk_hardware.py

@@ -15,6 +15,7 @@ from quisk_hardware_model import Hardware as BaseHardware
 
 DEBUG = 0
 DEBUG_I2C = 0
+DEBUG_SENSORS = 0
 
 class IOBoard:
   "This class controls the N2ADR IO Board for the HermesLite 2"
@@ -46,6 +47,8 @@ class IOBoard:
     self.old_receive = None
     self.slow = 0
   def HeartBeat(self):	# Called at 10 Hz for housekeeping tasks
+    if not self.hardware.is_HermesLite2:
+      return
     if not QS.get_params('rx_udp_started'):
       return
     if self.have_IO_Board is None:
@@ -154,6 +157,7 @@ class Hardware(BaseHardware):
     self.hermes_ip = ""
     self.hermes_code_version = -1
     self.hermes_board_id = -1
+    self.is_HermesLite2 = False
     self.hermes_temperature = 0.0
     self.hermes_fwd_power = 0.0
     self.hermes_rev_power = 0.0
@@ -166,7 +170,10 @@ class Hardware(BaseHardware):
     self.vna_count = 0
     self.vna_started = False
     self.repeater_freq = None		# original repeater output frequency
-    self.antenna_labels = ('Ant 0', 'Ant 1')	# labels for the antenna button
+    if conf.hardware_file_type == "Red Pitaya":
+      self.antenna_labels = ('Ant 0', 'Ant 1')	# labels for the antenna button
+    else:
+      self.antenna_labels = ('Ant 0', 'Ant 1', 'Ant 2', 'Ant 3')
     self.antenna_index = 0			# index of antenna in use
     self.delay_config = True			# Delay sending message to HL2 until after sound starts
     self.TFRC_counter = 0		# Call for power etc. at intervals
@@ -271,6 +278,7 @@ class Hardware(BaseHardware):
             self.hermes_ip = addr[0]
             self.hermes_code_version = data[9]
             self.hermes_board_id = data[10]
+            self.is_HermesLite2 = self.hermes_board_id == 6 and self.conf.hardware_file_type == "Hermes"
             QS.set_hermes_id(data[9], data[10])
             if data[0x16] >> 6 == 0:
               QS.set_params(bandscopeScale = 2048)
@@ -317,6 +325,7 @@ class Hardware(BaseHardware):
       bid = 6
       self.hermes_code_version = code
       self.hermes_board_id = bid
+      self.is_HermesLite2 = self.hermes_board_id == 6 and self.conf.hardware_file_type == "Hermes"
       QS.set_hermes_id(code, bid)
       st = 'Capture from Hermes device at specified IP %s' % self.hermes_ip
       found = True
@@ -331,9 +340,13 @@ class Hardware(BaseHardware):
   def open(self):
     self.delay_config = True	# Delay sending message to HL2 until after sound starts
     # This list only changes control bits; no use of WriteQueue()
-    for name in ('keyupDelay',
-        'hermes_lowpwr_tr_enable', 'hermes_PWM', 'hermes_disable_sync', 'hermes_power_amp', 'Hermes_BandDictEnTx'):
-      self.ImmediateChange(name)
+    self.ImmediateChange('keyupDelay')
+    self.ImmediateChange('Hermes_BandDictEnTx')
+    if self.is_HermesLite2:
+      for name in ('hermes_lowpwr_tr_enable', 'hermes_PWM', 'hermes_disable_sync', 'hermes_power_amp'):
+        self.ImmediateChange(name)
+    #else:	# DEBUG: Turn on power amp for testing OpenHPSDR radio with my Hermes Lite2
+    #  self.SetControlBit(0x09, 19, 1)
     return self.config_text
   def GetValue(self, name):	# return values stored in the hardware
     if name == 'Hware_Hl2_EepromIP':
@@ -492,7 +505,15 @@ class Hardware(BaseHardware):
     self.key_was_down = key_down
     if self.TFRC_counter >= 3:
       self.TFRC_counter = 0
-      self.hermes_temperature, self.hermes_fwd_power, self.hermes_rev_power, self.hermes_pa_current, self.hermes_fwd_peak, self.hermes_rev_peak = QS.get_hermes_TFRC()
+      AIN1_avg, AIN1_peak, AIN2_avg, AIN2_peak, AIN3, AIN4, AIN5, AIN6 = QS.get_hermes_TFRC()
+      if self.hermes_board_id == 6:
+        (self.hermes_fwd_power, self.hermes_fwd_peak, self.hermes_rev_power, self.hermes_rev_peak,
+         self.hermes_pa_current, self.hermes_temperature) = AIN1_avg, AIN1_peak, AIN2_avg, AIN2_peak, AIN3, AIN5
+      else:
+        (self.hermes_fwd_power, self.hermes_fwd_peak, self.hermes_rev_power, self.hermes_rev_peak,
+         self.hermes_pa_current, self.hermes_temperature) = AIN1_avg, AIN1_peak, AIN2_avg, AIN2_peak, AIN3, AIN5
+      if DEBUG_SENSORS:
+        print("AIN 1-6 %4d %4d %4d %4d %4d %4d" % (AIN1_avg, AIN2_avg, AIN3, AIN4, AIN5, AIN6))
       if self.application.bottom_widgets:
         self.application.bottom_widgets.UpdateText()
     if self.delay_config and QS.get_params('rx_udp_started'):
@@ -529,7 +550,9 @@ class Hardware(BaseHardware):
   def ChangeBandFilters(self):
     if not hasattr(self.application, "multi_rx_screen"):
       return	# Needed for the VNA program
-    self.SetControlBit(0x00, 13, self.antenna_index)
+    self.SetControlBit(0x00, 13, self.antenna_index & 0x01)
+    self.SetControlBit(0x00, 14, self.antenna_index & 0x02)
+    self.SetControlBit(0x00, 15, self.antenna_index > 0)
     highest = self.band
     freq = self.conf.BandEdge.get(highest, (0, 0))[0]
     for pane in self.application.multi_rx_screen.receiver_list:
@@ -606,12 +629,7 @@ class Hardware(BaseHardware):
     return (48000, 384000)
   ## Hardware AGC is no longer supported in HL2 identifying as version >=40   
   def ChangeAGC(self, value):
-    if value:
-      self.pc2hermes[2] |= 0x10		# C0 index == 0, C3[4]: AGC enable
-    else:
-      self.pc2hermes[2] &= ~0x10
-    QS.pc_to_hermes(self.pc2hermes)
-    if DEBUG: print ("Change AGC to", value)
+    pass
   ## Simpler LNA setting for HL2 identifying as version >=40, see HL2 wiki for details
   def ChangeLNA(self, value):		# LNA for Rx
     # value is -12 to +48
@@ -624,7 +642,7 @@ class Hardware(BaseHardware):
         value = 51 - value
     else:
       value = ((value+12) & 0x3f) | 0x40
-    self.pc2hermes[4 * 10 + 3] = value			# C0 index == 0x1010, C4[4:0] LNA 0-32 dB gain
+    self.pc2hermes[4 * 10 + 3] = value			# C0 index == 0b1010, C4[4:0] LNA 0-32 dB gain
     QS.pc_to_hermes(self.pc2hermes)
     if DEBUG: print ("Change LNA to", value)
   def ChangeTxLNA(self, value):		# LNA for Tx
@@ -634,9 +652,17 @@ class Hardware(BaseHardware):
     elif value > 48:
       value = 48
     value = ((value+12) & 0x3f) | 0x40 | 0x80
-    self.SetControlByte(0x0e, 3, value, False)		# C0 index == 0x0e, C3
+    self.SetControlByte(0x0e, 3, value, False)		# C0 index == 0b1110 == 0x0e, C3
     QS.pc_to_hermes(self.pc2hermes)
     if DEBUG: print ("Change Tx LNA to", value)
+  def ChangeAtten(self, value):
+    # value is 0 to 31
+    self.pc2hermes[4 * 10 + 3] = value & 0x1F			# C0 index == 0b1010, C4[4:0] attenuator, 0 to 31 dB
+    self.SetControlBit(0b1010, 5, value)			# enable attenuator
+    QS.pc_to_hermes(self.pc2hermes)
+    if DEBUG: print ("Change attenuator to", value)
+  def ChangePreamp(self, value):
+    self.SetControlBit(0b0000, 10, value)			# enable preamp
   def SetTxLevel(self):
     try:
       tx_level = self.conf.tx_level[self.band]
@@ -653,7 +679,7 @@ class Hardware(BaseHardware):
       tx_level = 0
     elif tx_level > 255:
       tx_level = 255
-    self.pc2hermes[4 * 9] = tx_level			# C0 index == 0x1001, C1[7:0] Tx level
+    self.pc2hermes[4 * 9] = tx_level			# C0 index == 0b1001, C1[7:0] Tx level
     QS.pc_to_hermes(self.pc2hermes)
     if DEBUG: print("Change tx_level to", tx_level)
   def MultiRxCount(self, count):	# count == number of additional receivers besides the Tx/Rx receiver: 1, 2, 3
@@ -876,6 +902,8 @@ class Hardware(BaseHardware):
       QS.set_hermeslite_writepointer(0)
     return False
   def WriteQueue(self, wait=False):
+    if not self.is_HermesLite2:
+      return False
     self._wait_queue()
     # Send next write
     self.old_writequeue = self.pc2hermeslitewritequeue[:]

hermes/quisk_widgets.py

@@ -154,6 +154,12 @@ class BottomWidgets:	# Add extra widgets to the bottom of the screen
     current = " PA %4.0f ma" % (1000*current)
     self.text_pa_current.SetLabel(current)
     # forward and reverse peak power
+    if not self.hardware.power_interpolator:	# For no interpolator, show ADC
+      fwd = self.hardware.hermes_fwd_power
+      rev = self.hardware.hermes_rev_power
+      self.text_fwd_power.SetLabel("Fwd ADC %4d" % fwd)
+      self.text_swr.SetLabel("Rev ADC %4d" % rev)
+      return
     fwd, rev = self.Code2FwdRevWatts(self.hardware.hermes_fwd_peak, self.hardware.hermes_rev_peak)
     # forward less reverse power
     power = fwd - rev

n2adr/hl2_hardware.py

@@ -1,8 +1,5 @@
 # This is the hardware control file for my shack.
-# It is for the Hermes-Lite2 5 watt output which uses only the antenna tuner.
-from __future__ import print_function
-from __future__ import absolute_import
-from __future__ import division
+# It is for the Hermes-Lite2 RF1 output and Alt Rx input.
 
 from hermes.quisk_hardware import Hardware as BaseHw
 from n2adr import station_hardware
@@ -17,7 +14,7 @@ class Hardware(BaseHw):
     self.controlbox = station_hardware.ControlBox(app, conf)	# Control my Station Control Box
     self.v2filter = station_hardware.FilterBoxV2(app, conf)	# Control V2 filter box
   def open(self):
-    if False:
+    if False:	# Start the station control GUI
       from n2adr.station_hardware import StationControlGUI
       self.GUI = StationControlGUI(self.application.main_frame, self, self.application, self.conf)
       self.GUI.Show()
@@ -29,12 +26,11 @@ class Hardware(BaseHw):
     return BaseHw.close(self)
   def ChangeFilterFrequency(self, tx_freq):
     if tx_freq and tx_freq > 0:
+      self.v2filter.SetTxFreq(tx_freq)
       if self.GUI:
         self.GUI.SetTxFreq(tx_freq)
-        self.GUI.freq_entry.ChangeValue("%.3f" % (tx_freq * 1E-6))
       else:
         self.anttuner.SetTxFreq(tx_freq)
-        self.v2filter.SetTxFreq(tx_freq)
   def ChangeFrequency(self, tx_freq, vfo_freq, source='', band='', event=None):
     self.ChangeFilterFrequency(tx_freq)
     return BaseHw.ChangeFrequency(self, tx_freq, vfo_freq, source, band, event)
@@ -42,8 +38,6 @@ class Hardware(BaseHw):
     # band is a string: "60", "40", "WWV", etc.
     ret = BaseHw.ChangeBand(self, band)
     self.anttuner.ChangeBand(band)
-    #self.lpfilter.ChangeBand(band)
-    #self.hpfilter.ChangeBand(band)
     self.v2filter.ChangeBand(band)
     self.CorrectSmeter()
     return ret

n2adr/quisk_widgets.py

@@ -1,56 +1,10 @@
-# Please do not change this widgets module for Quisk.  Instead copy
-# it to your own quisk_widgets.py and make changes there.
-#
 # This module is used to add extra widgets to the QUISK screen.
 
-from __future__ import print_function
-from __future__ import absolute_import
-from __future__ import division
-
 import wx, time
 import _quisk as QS
 
-class BottomWidgets:	# Add extra widgets to the bottom of the screen
+from hermes.quisk_widgets import BottomWidgets as BaseWidgets
+
+class BottomWidgets(BaseWidgets):	# Add extra widgets to the bottom of the screen
   def __init__(self, app, hardware, conf, frame, gbs, vertBox):
-    #self.config = conf
-    #self.hardware = hardware
-    #self.application = app
-    #start_row = app.widget_row			# The first available row
-    #start_col = app.button_start_col	# The start of the button columns
-    #b = app.QuiskCycleCheckbutton(frame, self.OnAntTuner, ('Antenna', 'Ant 0', 'Ant 1'))
-    #bw, bh = b.GetMinSize()
-    #gbs.Add(b, (start_row, start_col), (1, 2), flag=wx.EXPAND)
-    #b = app.QuiskPushbutton(frame, self.OnAntTuner, 'L+')
-    #b.Enable(0)
-    #gbs.Add(b, (start_row, start_col + 2), (1, 2), flag=wx.EXPAND)
-    #b = app.QuiskPushbutton(frame, self.OnAntTuner, 'L-')
-    #b.Enable(0)
-    #gbs.Add(b, (start_row, start_col + 4), (1, 2), flag=wx.EXPAND)
-    #b = app.QuiskPushbutton(frame, self.OnAntTuner, 'C+')
-    #b.Enable(0)
-    #gbs.Add(b, (start_row, start_col + 6), (1, 2), flag=wx.EXPAND)
-    #b = app.QuiskPushbutton(frame, self.OnAntTuner, 'C-')
-    #b.Enable(0)
-    #gbs.Add(b, (start_row, start_col + 8), (1, 2), flag=wx.EXPAND)
-    #b = app.QuiskPushbutton(frame, self.OnAntTuner, 'Save')
-    #b.Enable(0)
-    #gbs.Add(b, (start_row, start_col + 10), (1, 2), flag=wx.EXPAND)
-    #self.swr_label = app.QuiskText(frame, 'Watts 000   SWR 10.1  Zh Ind 22 Cap 33   Freq 28100 (7777)', bh)
-    #gbs.Add(self.swr_label, (start_row, start_col + 2), (1, 10), flag=wx.EXPAND)
-    #b = app.QuiskCheckbutton(frame, None, text='')
-    #gbs.Add(b, (start_row, start_col + 25), (1, 2), flag=wx.EXPAND)
-#  Example of a horizontal slider:
-#    lab = wx.StaticText(frame, -1, 'Preamp', style=wx.ALIGN_CENTER)
-#    gbs.Add(lab, (5,0), flag=wx.EXPAND)
-#    sl = wx.Slider(frame, -1, 1024, 0, 2048)	# parent, -1, initial, min, max
-#    gbs.Add(sl, (5,1), (1, 5), flag=wx.EXPAND)
-#    sl.Bind(wx.EVT_SCROLL, self.OnPreamp)
-#  def OnPreamp(self, event):
-#    print event.GetPosition()
-    self.num_rows_added = 0
-  #def OnAntTuner(self, event):
-  #  btn = event.GetEventObject()
-  #  text = btn.GetLabel()
-  #  self.hardware.OnAntTuner(text)
-  #def UpdateText(self, text):
-  #  self.swr_label.SetLabel(text)
+    BaseWidgets.__init__(self, app, hardware, conf, frame, gbs, vertBox)

n2adr/station_hardware.py

@@ -1,9 +1,5 @@
 # This file supports various hardware boxes at my shack
 
-from __future__ import print_function
-from __future__ import absolute_import
-from __future__ import division
-
 import sys, struct, math, socket, select, time, traceback, os
 import wx, wx.lib.buttons
 
@@ -411,18 +407,15 @@ class AntennaTuner:     # Control my homebrew antenna tuner and my KI8BV dipole
     self.set_HighZ = 0
     self.antnum = 0				# Antenna number 0 or 1
     self.dipole2 = AntennaControl(app, conf)	# Control the KI8BV dipole
-    if False and conf.use_rx_udp == 10:		# Hermes UDP protocol for Hermes-Lite2
-      path = 'TunerLCZ_HL2.txt'
-    else:
-      path = 'TunerLCZ.txt'
+    path = 'TunerLCZ.txt'
     if sys.platform == "win32":
-      path = 'C:/pub/' + path
+      self.path = 'C:/pub/' + path
     else:
-      path = '/home/jim/pub/' + path
-    fp = open(path, "r")
+      self.path = '/home/jim/pub/' + path
+    fp = open(self.path, "r")
     lines = fp.readlines()
     fp.close()
-    self.TunerLCZ = [(0, 0, 0, 0), (999111000, 0, 0, 0)]	# Add dummy first and last entry.
+    self.TunerLCZ = []
     for line in lines:
       freq, antL, antC, hilo = line.split()
       freq = int(freq)
@@ -451,7 +444,12 @@ class AntennaTuner:     # Control my homebrew antenna tuner and my KI8BV dipole
     pass
   def ChangeBand(self, band):
     pass
-  def FindLCZ(self, tx_freq):
+  def SaveLCZ(self):
+    fp = open(self.path, 'w')
+    for tup in self.TunerLCZ:
+      fp.write("%12d %2d %2d %d\n" % tup)
+    fp.close()
+  def FindIndexTup(self, tx_freq):
     i1 = 0
     i2 = len(self.TunerLCZ) - 1
     while 1:	# binary partition
@@ -462,20 +460,14 @@ class AntennaTuner:     # Control my homebrew antenna tuner and my KI8BV dipole
         i2 = i
       if i2 - i1 <= 1:
         break
-    # The correct setting is between i1 and i2.
+    # The correct setting is between i1 and i2, or below i1 or above i2.
     # Choose the index that is closest in frequency.
-    delta1 = tx_freq - self.TunerLCZ[i1][0]
-    delta2 = self.TunerLCZ[i2][0] - tx_freq
-    if i1 == 0:				# below the first frequency
+    if abs(tx_freq - self.TunerLCZ[i1][0]) < abs(tx_freq - self.TunerLCZ[i2][0]):
       index = i1
-    elif i2 == len(self.TunerLCZ) - 1:	# above the last frequency
+    else:
       index = i2
-    elif delta2 < delta1:	# i2 is closer
-      index = i2
-    else:			# i1 is closer
-      index = i1
-    if DEBUG: print ("AntennaTuner FindLCZ", tx_freq, i1, i2, len(self.TunerLCZ), self.TunerLCZ[index])
-    return self.TunerLCZ[index]
+    if DEBUG: print ("StatuinControlGUI FindIndexTup", tx_freq, i1, i2, len(self.TunerLCZ), index, self.TunerLCZ[index])
+    return index, self.TunerLCZ[index]
   def SetTxFreq(self, tx_freq, no_tune=False):
     #if DEBUG: print("AntennaTuner SetTxFreq", tx_freq)
     self.tx_freq = tx_freq
@@ -484,10 +476,10 @@ class AntennaTuner:     # Control my homebrew antenna tuner and my KI8BV dipole
     if tx_freq < 17000000:
       if DEBUG and self.antnum == 1: print ("antnum 0")
       self.antnum = 0
-    else:
+    elif self.dipole2:
       if DEBUG and self.antnum == 0: print ("antnum 1")
       self.antnum = 1
-    if self.antnum == 1:
+    if self.antnum == 1 and self.dipole2:
       self.dipole2.SetTxFreq(tx_freq)
     if not self.socket:
       return
@@ -496,7 +488,7 @@ class AntennaTuner:     # Control my homebrew antenna tuner and my KI8BV dipole
     if abs(self.tune_freq - tx_freq) < 5000:		# ignore small changes
       return
     self.tune_freq = tx_freq
-    f, newL, newC, newH = self.FindLCZ(tx_freq)
+    index, (f, newL, newC, newH) = self.FindIndexTup(tx_freq)
     if newH != self.set_HighZ or self.set_C != newC or self.set_L != newL:
       self.set_HighZ = newH
       self.set_C = newC
@@ -521,7 +513,8 @@ class AntennaTuner:     # Control my homebrew antenna tuner and my KI8BV dipole
         self.timer = 0
     else:
       self.timer = 0
-    self.dipole2.HeartBeat()
+    if self.dipole2:
+      self.dipole2.HeartBeat()
   def Send(self):
     try:
       self.socket.send(self.want_data)
@@ -539,26 +532,7 @@ class StationControlGUI(wx.Frame):    # Display a stand-alone control window for
     self.conf = conf
     self.data_saving = False
     self.tx_freq = 0
-    if sys.platform == "win32":
-      self.filename = 'C:/pub/TunerLCZ.tmp'
-    else:
-      self.filename = '/home/jim/pub/TunerLCZ.tmp'
-    try:
-      fp = open(self.filename, "r")
-    except FileNotFoundError:
-      lines = ()
-    else:
-      lines = fp.readlines()
-      fp.close()
-    self.TunerLCZ = [(0, 0, 0, 0), (999111000, 0, 0, 0)]	# Add dummy first and last entry.
-    for line in lines:
-      freq, antL, antC, hilo = line.split()
-      freq = int(freq)
-      antL = int(antL)
-      antC = int(antC)
-      hilo = int(hilo)
-      self.TunerLCZ.append((freq, antL, antC, hilo))
-    self.TunerLCZ.sort()
+    self.anttuner = self.hware.anttuner
     self.SetBackgroundColour('light steel blue')
     self.Bind(wx.EVT_CHAR_HOOK, self.OnKeyDown)
     sizer = wx.GridBagSizer(hgap=5, vgap=3)
@@ -568,6 +542,7 @@ class StationControlGUI(wx.Frame):    # Display a stand-alone control window for
     self.bands = []
     for band in ('160', '80', '60', '40', '30', '20', '17', '15', '12', '10'):
       b = wx.lib.buttons.GenToggleButton(self, -1, band)
+      b.Enable(False)
       b.SetUseFocusIndicator(False)
       b.SetBezelWidth(4)
       self.bands.append(b)
@@ -604,6 +579,7 @@ class StationControlGUI(wx.Frame):    # Display a stand-alone control window for
     szr = wx.BoxSizer(wx.HORIZONTAL)
     szr.AddSpacer(20)
     b = wx.lib.buttons.GenToggleButton(self, -1, "Key Down")
+    b.Enable(False)
     b.SetFont(font)
     b.SetUseFocusIndicator(False)
     b.SetBezelWidth(4)
@@ -611,6 +587,7 @@ class StationControlGUI(wx.Frame):    # Display a stand-alone control window for
     szr.Add(b)
     szr.AddSpacer(10)
     b = wx.lib.buttons.GenToggleButton(self, -1, "FilterV2 Preamp")
+    b.Enable(False)
     b.SetFont(font)
     b.SetUseFocusIndicator(False)
     b.SetBezelWidth(4)
@@ -622,16 +599,31 @@ class StationControlGUI(wx.Frame):    # Display a stand-alone control window for
     b.SetFont(font)
     szr.Add(b, flag=wx.ALIGN_CENTER_VERTICAL)
     szr.AddSpacer(10)
-    self.freq_entry = wx.TextCtrl(self, value='0000.000', style=wx.TE_PROCESS_ENTER)
+    self.freq_entry = wx.StaticText(self, -1, "0000.000")
+    #self.freq_entry = wx.TextCtrl(self, value='0000.000', style=wx.TE_PROCESS_ENTER)
     self.freq_entry.SetFont(font)
-    self.Bind(wx.EVT_TEXT_ENTER, self.OnFreqEntry, self.freq_entry)
-    szr.Add(self.freq_entry)
+    #self.Bind(wx.EVT_TEXT_ENTER, self.OnFreqEntry, self.freq_entry)
+    szr.Add(self.freq_entry, flag=wx.ALIGN_CENTER_VERTICAL)
     szr.AddSpacer(10)
-    b = wx.lib.buttons.GenButton(self, -1, "Search Freq")
+    b = wx.lib.buttons.GenButton(self, -1, "Freq-")
     b.SetUseFocusIndicator(False)
     b.SetBezelWidth(4)
     b.SetFont(font)
-    self.Bind(wx.EVT_BUTTON, self.OnButtonSearch, b)
+    self.Bind(wx.EVT_BUTTON, self.OnButtonDown, b)
+    szr.Add(b)
+    szr.AddSpacer(10)
+    b = wx.lib.buttons.GenButton(self, -1, "Freq+")
+    b.SetUseFocusIndicator(False)
+    b.SetBezelWidth(4)
+    b.SetFont(font)
+    self.Bind(wx.EVT_BUTTON, self.OnButtonUp, b)
+    szr.Add(b)
+    szr.AddSpacer(10)
+    b = wx.lib.buttons.GenButton(self, -1, "Delete")
+    b.SetUseFocusIndicator(False)
+    b.SetBezelWidth(4)
+    b.SetFont(font)
+    self.Bind(wx.EVT_BUTTON, self.OnButtonDelete, b)
     szr.Add(b)
     sizer.Add(szr, pos=(row, 0), span=(1, 3))
     if frame is None:
@@ -647,46 +639,22 @@ class StationControlGUI(wx.Frame):    # Display a stand-alone control window for
       self.Bind(wx.EVT_TIMER, self.HeartBeat)
       self.timer.Start(100)
   def SetTxFreq(self, tx_freq):
-    #print("StationControlGUI SetTxFreq", tx_freq)
+    tx_freq = ((tx_freq + 500) // 1000) * 1000
     self.tx_freq = tx_freq
-    index, tup = self.FindIndexTup(tx_freq)
+    anttuner = self.anttuner
+    index, tup = anttuner.FindIndexTup(tx_freq)
     self.sliderL.SetValue(tup[1])
     self.sliderC.SetValue(tup[2])
     self.btnHiLo.SetValue(tup[3])
-    anttuner = self.hware.anttuner
     fff, anttuner.set_L, anttuner.set_C, anttuner.set_HighZ = tup
     if tx_freq < 17000000:
       anttuner.antnum = 0
-    else:
+    elif anttuner.dipole2:
       anttuner.antnum = 1
-    if anttuner.antnum == 1:
+    if anttuner.antnum == 1 and anttuner.dipole2:
       anttuner.dipole2.SetTxFreq(tx_freq)
     anttuner.WantData()
-  def FindIndexTup(self, tx_freq):
-    i1 = 0
-    i2 = len(self.TunerLCZ) - 1
-    while 1:	# binary partition
-      i = (i1 + i2) // 2
-      if self.TunerLCZ[i][0] < tx_freq:
-        i1 = i
-      else:
-        i2 = i
-      if i2 - i1 <= 1:
-        break
-    # The correct setting is between i1 and i2.
-    # Choose the index that is closest in frequency.
-    delta1 = tx_freq - self.TunerLCZ[i1][0]
-    delta2 = self.TunerLCZ[i2][0] - tx_freq
-    if i1 == 0:				# below the first frequency
-      index = i1
-    elif i2 == len(self.TunerLCZ) - 1:	# above the last frequency
-      index = i2
-    elif delta2 < delta1:	# i2 is closer
-      index = i2
-    else:			# i1 is closer
-      index = i1
-    if DEBUG: print ("StatuinControlGUI FindLCZ", tx_freq, i1, i2, len(self.TunerLCZ), index, self.TunerLCZ[index])
-    return index, self.TunerLCZ[index]
+    self.freq_entry.SetLabel("%.3f" % (tx_freq * 1E-6))
   def OnBtnClose(self, event):
     self.hware.anttuner.close()
     self.hware.controlbox.close()
@@ -730,16 +698,15 @@ class StationControlGUI(wx.Frame):    # Display a stand-alone control window for
     f = ((f + 500) // 1000) * 1000
     if self.hware.v2filter:
       self.hware.v2filter.SetTxFreq(f)
-    self.hware.anttuner.SetTxFreq(f, no_tune=True)
+    self.anttuner.SetTxFreq(f, no_tune=True)
     self.freq_entry.ChangeValue("%.3f" % (f * 1E-6))
     self.SetTxFreq(f)
   def OnButtonHiLo(self, event):
-    anttuner = self.hware.anttuner
     if self.btnHiLo.GetValue():
-      anttuner.set_HighZ = 1
+      self.anttuner.set_HighZ = 1
     else:
-      anttuner.set_HighZ = 0
-    anttuner.WantData()
+      self.anttuner.set_HighZ = 0
+    self.anttuner.WantData()
   def OnFreqEntry(self, event=None):
     freq = self.freq_entry.GetValue()
     freq = float(freq) * 1E6
@@ -751,11 +718,27 @@ class StationControlGUI(wx.Frame):    # Display a stand-alone control window for
     freq = int(freq + 0.1)
     self.tx_freq = freq
     self.SetTxFreq(self.tx_freq)
+  def OnButtonDown(self, event):
+    index, tup = self.anttuner.FindIndexTup(self.tx_freq)
+    index -= 1
+    if index >= 0:
+      self.SetTxFreq(self.anttuner.TunerLCZ[index][0])
+  def OnButtonUp(self, event):
+    index, tup = self.anttuner.FindIndexTup(self.tx_freq)
+    index += 1
+    if index < len(self.anttuner.TunerLCZ):
+      self.SetTxFreq(self.anttuner.TunerLCZ[index][0])
+  def OnButtonDelete(self, event):
+    index, tup = self.anttuner.FindIndexTup(self.tx_freq)
+    if self.tx_freq == self.anttuner.TunerLCZ[index][0]:
+      del self.anttuner.TunerLCZ[index]
+    if index > 0:
+      self.SetTxFreq(self.anttuner.TunerLCZ[index - 1][0])
+    elif len(self.anttuner.TunerLCZ) > 0:
+      self.SetTxFreq(self.anttuner.TunerLCZ[0][0])
+    else:
+      self.SetTxFreq(0)
   def OnButtonSave(self, event):
-    freq = self.freq_entry.GetValue()
-    freq = float(freq) * 1E6
-    freq = int(freq + 0.1)
-    self.tx_freq = freq
     L = self.sliderL.GetValue()
     C = self.sliderC.GetValue()
     if self.btnHiLo.GetValue():
@@ -763,22 +746,19 @@ class StationControlGUI(wx.Frame):    # Display a stand-alone control window for
     else:
       hilo = 0
     tup = (self.tx_freq, L, C, hilo)
-    index, t = self.FindIndexTup(self.tx_freq)
-    if self.tx_freq == self.TunerLCZ[index][0]:
-      self.TunerLCZ[index] = tup
+    index, t = self.anttuner.FindIndexTup(self.tx_freq)
+    if self.tx_freq == self.anttuner.TunerLCZ[index][0]:
+      self.anttuner.TunerLCZ[index] = tup
     else:
-      self.TunerLCZ.append(tup)
-    self.TunerLCZ.sort()
-    fp = open(self.filename, 'w')
-    for tup in self.TunerLCZ[1:-1]:	# Throw away dummy entries
-      fp.write("%12d %2d %2d %d\n" % tup)
-    fp.close()
+      self.anttuner.TunerLCZ.append(tup)
+    self.anttuner.TunerLCZ.sort()
+    self.anttuner.SaveLCZ()
   def OnSliderL(self, event=None):
-    self.hware.anttuner.set_L = self.sliderL.GetValue()
-    self.hware.anttuner.WantData()
+    self.anttuner.set_L = self.sliderL.GetValue()
+    self.anttuner.WantData()
   def OnSliderC(self, event=None):
-    self.hware.anttuner.set_C = self.sliderC.GetValue()
-    self.hware.anttuner.WantData()
+    self.anttuner.set_C = self.sliderC.GetValue()
+    self.anttuner.WantData()
   def OnBtnV2Preamp(self, event):
     if self.hware.v2filter:
       self.hware.v2filter.SetPreamp(event.GetEventObject().GetValue())
@@ -1072,21 +1052,3 @@ class AT200PC:		# Control an AT-200PC autotuner made by LDG
         self.set_C += 1
       elif text == 'C-':
         self.set_C -= 1
-
-class App(wx.App):
-  def OnInit(self):
-    if sys.path[0] != "'.'":		# Make sure the current working directory is on path
-      sys.path.insert(0, '.')
-    import quisk_conf_defaults as conf
-    import quisk_hardware_model as hardware
-    self.bottom_widgets = None
-    hardware.anttuner = AntennaTuner(self, conf)	# Control the antenna tuner
-    hardware.v2filter = FilterBoxV2(self, conf)	# Control V2 filter box
-    hardware.controlbox = ControlBox(self, conf)	# Control my Station Control Box
-    self.main_frame = frame = StationControlGUI (None, hardware, self, conf)
-    frame.Open()
-    frame.Show()
-    return True
-
-if __name__ == '__main__':
-  App().MainLoop()

perseuspkg/quisk_hardware.py

@@ -18,7 +18,7 @@ from quisk_hardware_model import Hardware as BaseHardware
 DEBUG = 1
 
 # Define the name of the hardware and the items on the hardware screen (see quisk_conf_defaults.py):
-################ Receivers PerseusSDR, The PerseusSDR interface to multiple hardware SDRs.
+################ Receivers PerseusSDR, The PerseusSDR interface to multiple SDRs.
 ## hardware_file_name		Hardware file path, rfile
 # This is the file that contains the control logic for each radio.
 #hardware_file_name = 'perseuspkg/quisk_hardware.py'

quisk.c

@@ -218,14 +218,17 @@ static unsigned char quisk_hermes_to_pc[5 * 4];		// data received from the Herme
 static unsigned char quisk_hermeslite_response[5]; // response from Hermes-Lite commands
 unsigned int quisk_hermes_code_version = -1;		// code version returned by the Hermes hardware
 unsigned int quisk_hermes_board_id = -1;		// board ID returned by the Hermes hardware
-static double hermes_temperature;	// average temperature
-static double hermes_fwd_power;		// average forward power
-static double hermes_rev_power;		// average reverse power
-static double hermes_fwd_peak;		// peak forward power
-static double hermes_rev_peak;		// peak reverse power
-static double hermes_pa_current;	// average power amp current
-static int hermes_count_temperature;	// number of temperature samples
-static int hermes_count_current;	// number of current samples
+static double hpsdr_AIN1_avg;		// average forward power
+static double hpsdr_AIN1_peak;		// peak forward power
+static double hpsdr_AIN2_avg;		// average reverse power
+static double hpsdr_AIN2_peak;		// peak reverse power
+static double hpsdr_AIN3;		// average power amp current
+static double hpsdr_AIN4;
+static double hpsdr_AIN5;		// average temperature
+static double hpsdr_AIN6;
+static int hpsdr_AIN3_count;	// number of current samples
+static int hpsdr_AIN4_count;	// number of current samples
+static int hpsdr_AIN5_count;	// number of current samples
 static int hardware_ptt;		// hardware PTT switch
 
 int quisk_hardware_cwkey;		// hardware CW key from UDP or USB
@@ -3136,31 +3139,43 @@ static PyObject * get_hermes_TFRC(PyObject * self, PyObject * args)
 
 	if (!PyArg_ParseTuple (args, ""))
 		return NULL;
-	if (hermes_count_temperature > 0) {
-		hermes_temperature /= hermes_count_temperature;
-		hermes_fwd_power /= hermes_count_temperature;
+	if (hpsdr_AIN5_count > 0) {
+		hpsdr_AIN5 /= hpsdr_AIN5_count;
+		hpsdr_AIN1_avg /= hpsdr_AIN5_count;
 	}
 	else {
-		hermes_temperature  = 0.0;
-		hermes_fwd_power  = 0.0;
+		hpsdr_AIN5  = 0.0;
+		hpsdr_AIN1_avg  = 0.0;
 	}
-	if (hermes_count_current > 0) {
-		hermes_rev_power /= hermes_count_current;
-		hermes_pa_current /= hermes_count_current;
+	if (hpsdr_AIN3_count > 0) {
+		hpsdr_AIN2_avg /= hpsdr_AIN3_count;
+		hpsdr_AIN3 /= hpsdr_AIN3_count;
 	}
 	else {
-		hermes_rev_power  = 0.0;
-		hermes_pa_current  = 0.0;
+		hpsdr_AIN2_avg  = 0.0;
+		hpsdr_AIN3  = 0.0;
 	}
-	ret = Py_BuildValue("dddddd", hermes_temperature, hermes_fwd_power, hermes_rev_power, hermes_pa_current, hermes_fwd_peak, hermes_rev_peak);
-	hermes_temperature = 0;
-	hermes_fwd_power = 0;
-	hermes_rev_power = 0;
-	hermes_fwd_peak = 0;
-	hermes_rev_peak = 0;
-	hermes_pa_current = 0;
-	hermes_count_temperature = 0;
-	hermes_count_current = 0;
+	if (hpsdr_AIN4_count > 0) {
+		hpsdr_AIN4 /= hpsdr_AIN4_count;
+		hpsdr_AIN6 /= hpsdr_AIN4_count;
+	}
+	else {
+		hpsdr_AIN4  = 0.0;
+		hpsdr_AIN6  = 0.0;
+	}
+	ret = Py_BuildValue("dddddddd", hpsdr_AIN1_avg, hpsdr_AIN1_peak, hpsdr_AIN2_avg, hpsdr_AIN2_peak,
+		hpsdr_AIN3, hpsdr_AIN4, hpsdr_AIN5, hpsdr_AIN6);
+	hpsdr_AIN1_avg = 0;
+	hpsdr_AIN1_peak = 0;
+	hpsdr_AIN2_avg = 0;
+	hpsdr_AIN2_peak = 0;
+	hpsdr_AIN3 = 0;
+	hpsdr_AIN4 = 0;
+	hpsdr_AIN5 = 0;
+	hpsdr_AIN6 = 0;
+	hpsdr_AIN3_count = 0;
+	hpsdr_AIN4_count = 0;
+	hpsdr_AIN5_count = 0;
 	return ret;
 }
 
@@ -3708,19 +3723,24 @@ static int read_rx_udp10(complex double * samp)	// Read samples from UDP using t
 					quisk_set_play_state();
 				}
 			}
-			else if(dindex == 1) {	// temperature and forward power
-				hermes_temperature += quisk_hermes_to_pc[4] << 8 | quisk_hermes_to_pc[5];
+			else if(dindex == 1) {
+				hpsdr_AIN5 += quisk_hermes_to_pc[4] << 8 | quisk_hermes_to_pc[5];
 				power = quisk_hermes_to_pc[6] << 8 | quisk_hermes_to_pc[7];
-				hermes_fwd_power += power;
-				hermes_fwd_peak = fmax(hermes_fwd_peak, (double)power);
-				hermes_count_temperature++;
+				hpsdr_AIN1_avg += power;
+				hpsdr_AIN1_peak = fmax(hpsdr_AIN1_peak, (double)power);
+				hpsdr_AIN5_count++;
 			}
-			else if (dindex == 2) {	// reverse power and current
+			else if (dindex == 2) {
 				power = quisk_hermes_to_pc[8] << 8 | quisk_hermes_to_pc[9];
-				hermes_rev_power += power;
-				hermes_rev_peak = fmax(hermes_rev_peak, (double)power);
-				hermes_pa_current += quisk_hermes_to_pc[10] << 8 | quisk_hermes_to_pc[11];
-				hermes_count_current++;
+				hpsdr_AIN2_avg += power;
+				hpsdr_AIN2_peak = fmax(hpsdr_AIN2_peak, (double)power);
+				hpsdr_AIN3 += quisk_hermes_to_pc[10] << 8 | quisk_hermes_to_pc[11];
+				hpsdr_AIN3_count++;
+			}
+			else if (dindex == 3) {
+				hpsdr_AIN4 += quisk_hermes_to_pc[12] << 8 | quisk_hermes_to_pc[13];
+				hpsdr_AIN6 += quisk_hermes_to_pc[14] << 8 | quisk_hermes_to_pc[15];
+				hpsdr_AIN4_count++;
 			}
 			// convert 24-bit samples to 32-bit samples; int must be 32 bits.
 			index = start + 5;

quisk.py

@@ -995,17 +995,12 @@ class HamlibHandlerRig2:	# Test with telnet localhost 4532
     else:
       self.Send('0\n')
   def GetFreq(self):	# The Rx frequency
-    rx = self.app.multi_rx_screen.receiver_list
-    if rx:
-      rx = rx[0]
-      self.Reply('Frequency', rx.txFreq + rx.VFO, 0)
-      if HAMLIB_DEBUG:
-        print ("GetFreq rx", rx.txFreq, rx.VFO)
-    else:
-      self.Reply('Frequency', self.app.rxFreq + self.app.VFO, 0)
-      if HAMLIB_DEBUG:
-        print ("GetFreq app", self.app.rxFreq, self.app.txFreq, self.app.VFO)
+    # This is always the main Rx frequency without reference to added receivers.
+    self.Reply('Frequency', self.app.rxFreq + self.app.VFO, 0)
+    if HAMLIB_DEBUG:
+      print ("GetFreq app", self.app.rxFreq, self.app.txFreq, self.app.VFO)
   def SetFreq(self):	# The Rx frequency
+    # This is always the main Rx frequency without reference to added receivers.
     freq = self.GetParamNumber()
     try:
       freq = float(freq)
@@ -1014,12 +1009,7 @@ class HamlibHandlerRig2:	# Test with telnet localhost 4532
       self.ErrParam()
     else:
       freq = int(freq + 0.5)
-      # For multiple receivers this controls the first added receiver frequency; else it controls split Rx/Tx frequency.
-      rx = self.app.multi_rx_screen.receiver_list
-      if rx:
-        rx[0].ChangeRxTxFrequency(freq)
-      else:
-        self.app.ChangeRxTxFrequency(freq, None)
+      self.app.ChangeRxTxFrequency(freq, None)
   def GetSplitFreq(self):	# The Tx Frequency
     self.Reply('TX Frequency', self.app.txFreq + self.app.VFO, 0)
   def SetSplitFreq(self):	# The Tx Frequency
@@ -3728,7 +3718,7 @@ class App(wx.App):
   'wfallScaleZ', 'wfallGrScaleZ', 'graphScaleZ', 'split_rxtx_play', 'modeFilter',
   'file_name_rec_audio', 'file_name_rec_samples', 'file_name_rec_mic', 'file_name_rec_tmp',
   'file_name_play_audio', 'file_name_play_samples', 'file_name_play_cq',
-  'file_play_source', 'hermes_LNA_dB']
+  'file_play_source', 'hermes_LNA_dB', 'hermes_atten_dB']
   def __init__(self):
     global application
     QS.AppStatus(1)
@@ -3949,6 +3939,7 @@ class App(wx.App):
     self.serial_ptt_active = False
     self.vox_ptt_active = False
     self.hermes_LNA_dB = 20
+    self.hermes_atten_dB = 0
     if hasattr(Hardware, "OnChangeRxTx"):
       self.want_RxTx = True
     else:
@@ -6808,7 +6799,7 @@ class App(wx.App):
     if self.timer - self.heart_time0 > 0.10:	# call hardware to perform background tasks:
       self.heart_time0 = self.timer
       Hardware.HeartBeat()
-      if conf.hermes_lite2_enable:
+      if Hardware.is_HermesLite2:
         self.tx_inhibit = QS.get_params('quisk_tx_inhibit')
       else:
         self.tx_inhibit = 0

quisk_conf_defaults.py

@@ -48,7 +48,7 @@ quisk_widgets = None
 
 
 
-################ Receivers SoftRock USB, Devices controlled by USB that capture samples from a sound card, and (for Tx) play samples to a sound card
+################ Receivers SoftRock USB, Sound card radios controlled by USB.
 ## hardware_file_name		Hardware file path, rfile
 # This is the file that contains the control logic for each radio.
 #hardware_file_name = 'softrock/hardware_usb.py'
@@ -133,7 +133,7 @@ digital_tx_level = 100
 
 
 
-################ Receivers SoftRock Fixed, Fixed frequency devices that capture samples from a sound card, and (for Tx) play samples to a sound card
+################ Receivers SoftRock Fixed, Fixed frequency sound card radios.
 ## hardware_file_name		Hardware file path, rfile
 # This is the file that contains the control logic for each radio.
 #hardware_file_name = 'quisk_hardware_fixed.py'
@@ -174,7 +174,7 @@ digital_tx_level = 100
 
 
 
-################ Receivers HiQSDR, The original N2ADR hardware and the improved HiQSDR using UDP
+################ Receivers HiQSDR, The original N2ADR and HiQSDR radios.
 ## hardware_file_name		Hardware file path, rfile
 # This is the file that contains the control logic for each radio.
 #hardware_file_name = 'hiqsdr/quisk_hardware.py'
@@ -258,7 +258,7 @@ sndp_active = True
 
 
 
-################ Receivers Hermes, The Hermes-Lite Project and possibly other hardware with the Hermes FPGA code.
+################ Receivers Hermes, The Hermes-Lite project by Steve Haynal.
 ## hardware_file_name		Hardware file path, rfile
 # This is the file that contains the control logic for each radio.
 #hardware_file_name = 'hermes/quisk_hardware.py'
@@ -275,7 +275,7 @@ sndp_active = True
 # You can set these options:
 
 ## use_rx_udp			Hardware type, integer choice
-# This is the type of UDP hardware.  Use 10 for the Hermes protocol.
+# This is the type of UDP hardware.  Use 10 for the Hermes Lite2 protocol.
 #use_rx_udp = 10
 
 ## udp_rx_ip		Hermes known IP, text
@@ -373,6 +373,7 @@ hermes_disable_sync = False
 # be sure to write it down. To use this address you must set "Eeprom IP Usage".
 # And you may want to set "Hermes known IP" too. Make sure the address does not conflict
 # with your DHCP server.
+# Power cycle the HL2 after changing this item.
 Hware_Hl2_EepromIP = '192.168.1.6'
 #Hware_Hl2_EepromIP = '192.168.1.241'
 
@@ -380,6 +381,7 @@ Hware_Hl2_EepromIP = '192.168.1.6'
 # This is the way the EEPROM IP address is used at power on.
 # "Ignore" means it is not used at all. "Set address" means DHCP is not used and the EEPROM IP address is used.
 # "Use DHCP first" means the EEPROM IP address is only used if DHCP fails.
+# Power cycle the HL2 after changing this item.
 Hware_Hl2_EepromIPUse = 'Ignore'
 #Hware_Hl2_EepromIPUse = 'Use DHCP first'
 #Hware_Hl2_EepromIPUse = 'Set address'
@@ -390,6 +392,7 @@ Hware_Hl2_EepromIPUse = 'Ignore'
 # at power on instead of the factory supplied MAC address 0:1c:c0:a2:13:dd. It is only used at power on,
 # and it is only used if it is marked valid by setting "Eeprom MAC usage" to "Set address".
 # If you have two HL2's, you must have a unique MAC address for each.
+# Power cycle the HL2 after changing this item.
 Hware_Hl2_EepromMAC = '0xA1 0x6B'
 #Hware_Hl2_EepromMAC = '0x4C 0x33'
 
@@ -398,6 +401,7 @@ Hware_Hl2_EepromMAC = '0xA1 0x6B'
 # the HL2 will use the last two MAC bytes from "Eeprom MAC address"; otherwise the default MAC is used.
 # If you change this item, the bit is written to the HL2.
 # The HL2 only uses these bits at power on.
+# Power cycle the HL2 after changing this item.
 Hware_Hl2_EepromMACUse = 'Ignore'
 #Hware_Hl2_EepromMACUse = 'Set address'
 
@@ -474,13 +478,6 @@ hermes_iob_rxin = 'J10 available'
 #hermes_iob_rxin = 'HL2 Rx to J9'
 #hermes_iob_rxin = 'Use J9 and J10'
 
-## hermes_lite2_enable			Hermes Lite2 protocol, boolean
-# This turns on some of the protocol extensions for the Hermes Lite2 that are not part
-# of the official Hermes Protocol 1. Currently this only enables Tx Inhibit (CN8).
-# Changes are immediate (no need to restart).
-hermes_lite2_enable = True
-#hermes_lite2_enable = False
-
 
 # These are known power meter calibration tables. This table is not present in the JSON settings file.
 power_meter_std_calibrations = {}
@@ -491,6 +488,7 @@ power_meter_std_calibrations['HL2FilterE3'] = [[ 0, 0.0 ], [ 25.865384615384617,
           [ 4093.1785714285716, 7.28994845808807 ], [ 4502.496428571429, 8.820837634286566 ], [ 4952.746071428572, 10.673213537486745 ] ]
 #power_meter_std_calibrations['HL2FilterE1'] = [[0, 0.0], [9.07, 0.002], [54.98, 0.014], [148.6, 0.057],
 #          [328.0, 0.208], [611.1, 0.646], [807.0, 1.098], [982.1, 1.6], [1223.3, 2.471], [1517.7, 3.738], [1758.7, 5.02]]
+power_meter_std_calibrations['Show ADC'] = []
 
 ## Hermes_BandDict		Rx IO Bus, dict
 # The Hermes_BandDict sets the 7 bits on the J16 connector for Rx.
@@ -508,17 +506,17 @@ Hermes_BandDictEnTx = False
 #Hermes_BandDictEnTx = True
 
 
-################ Receivers Red Pitaya, The Red Pitaya Project by Pavel Demin.  This uses the Hermes FPGA code.
+################ Receivers Red Pitaya, The Red Pitaya project by Pavel Demin.
 ## hardware_file_name		Hardware file path, rfile
 # This is the file that contains the control logic for each radio.
 #hardware_file_name = 'hermes/quisk_hardware.py'
 
 ## widgets_file_name			Widget file path, rfile
 # This optional file adds additional controls for the radio.
-#widgets_file_name = ''
+#widgets_file_name = 'hermes/hpsdr_widgets.py'
 
 ## use_rx_udp			Hardware type, integer choice
-# This is the type of UDP hardware.  Use 10 for the Hermes protocol.
+# This is the type of UDP hardware.  Use 10 for the Red Pitaya using the OpenHPSDR protocol.
 #use_rx_udp = 10
 
 ## rx_udp_ip				IP change, text
@@ -586,7 +584,123 @@ Hermes_BandDictEnTx = False
 #Hermes_BandDictEnTx = True
 
 
-################ Receivers SoapySDR, The SoapySDR interface to multiple hardware SDRs.
+################ Receivers OpenHPSDR, Radios using the HPSDR Protocol 1.
+## hardware_file_name		Hardware file path, rfile
+# This is the file that contains the control logic for each radio.
+#hardware_file_name = 'hermes/quisk_hardware.py'
+
+## widgets_file_name			Widget file path, rfile
+# This optional file adds additional controls for the radio.
+#widgets_file_name = 'hermes/hpsdr_widgets.py'
+
+## use_rx_udp			Hardware type, integer choice
+# This is the type of UDP hardware.  Use 10 for hardware using the OpenHPSDR protocol 1.
+#use_rx_udp = 10
+
+## rx_udp_ip				IP change, text
+# This item should be left blank. It is used to change the IP address of the hardware to a different
+# IP once the hardware is found. Not all Hermes firmware supports changing the IP address.
+#rx_udp_ip = ""
+
+## rx_udp_port				Hardware UDP port, integer
+# This is the UDP port number of your hardware.
+#rx_udp_port = 1024
+
+## rx_udp_ip_netmask		Network netmask, text
+# This is the netmask for the network.
+#rx_udp_ip_netmask = '255.255.255.0'
+
+## tx_ip					Transmit IP, text
+# Leave this blank to use the same IP address as the receive hardware.  Otherwise, enter "disable"
+# to disable sending transmit I/Q samples, or enter the actual IP address.  You must enter "disable"
+# if you have multiple hardwares on the network, and only one should transmit. This item is normally blank.
+tx_ip = ""
+#tx_ip = "disable"
+
+## tx_audio_port			Tx audio UDP port, integer
+# This is the UDP port for transmit audio I/Q samples.  Enter zero to calculate this from the
+# base hardware port.  Otherwise enter the special custom port.
+tx_audio_port = 0
+
+## rx_udp_clock				Clock frequency Hertz, integer
+# This is the clock frequency of the hardware in Hertz.
+#rx_udp_clock = 122880000
+#rx_udp_clock = 76800000
+#rx_udp_clock = 125000000
+
+## tx_level		Tx Level, dict
+# This sets the transmit level 0 to 255 for each band.
+# The config screen has a slider 0 to 100% so you can reduce the transmit power.
+# The hardware only supports a limited adjustment range, so zero is still a small amount of power.
+tx_level = {}
+
+## digital_tx_level			Digital Tx power %, integer
+# Digital modes reduce power by the percentage on the config screen.
+# This is the maximum value of the slider.
+#digital_tx_level = 100
+
+## hermes_code_version		Hermes code version, integer
+# There can be multiple Hermes devices on a network, but Quisk can only use one of these.  If you have multiple
+# hermes devices, you can use this to specify a unique device.  Or use -1 to accept any board.
+hermes_code_version = -1
+
+## hermes_board_id			Hermes board ID, integer
+# There can be multiple Hermes devices on a network, but Quisk can only use one of these.  If you have multiple
+# hermes devices, you can use this to specify a unique device.  Or use -1 to accept any board.
+hermes_board_id = -1
+
+## Hermes_BandDict		Hermes Bus, dict
+# The Hermes_BandDict sets the 7 bits on the J16 connector.
+Hermes_BandDict = {
+	'160':0b0000001, '80':0b0000010, '60':0b0000100, '40':0b0001000, '30':0b0010000, '20':0b0100000, '15':0b1000000}
+
+## Hermes_BandDictTx		Tx IO Bus, dict
+# The Hermes_BandDictTx sets the 7 bits on the J16 connector for Tx if enabled.
+Hermes_BandDictTx = {'160':0, '80':0, '60':0, '40':0, '30':0, '20':0, '17':0, '15':0, '12':0, '10':0}
+
+## Hermes_BandDictEnTx		Enable Tx Filt, boolean
+# Enable the separate Rx and Tx settings for the J16 connector.
+Hermes_BandDictEnTx = False
+#Hermes_BandDictEnTx = True
+
+## calibrate_temp_20			PA temp ADC at 20\u2103, integer
+# This is the ADC code returned for a temperature of 20C.
+# To see the ADC code being returned, enter zero for both temperature codes.
+# Linear interpolation is used to calculate the temperature.
+# Changes are immediate (no need to restart).
+calibrate_temp_20 = 0
+
+## calibrate_temp_40			PA temp ADC at 40\u2103, integer
+# This is the ADC code returned for a temperature of 40C.
+# To see the ADC code being returned, enter zero for both temperature codes.
+# Linear interpolation is used to calculate the temperature.
+# Changes are immediate (no need to restart).
+calibrate_temp_40 = 0
+
+## calibrate_current_0			PA current ADC at zero, integer
+# This is the ADC code returned for a PA current of zero.
+# To see the ADC code being returned, enter zero for both current codes.
+# Linear interpolation is used to calculate the current.
+# Changes are immediate (no need to restart).
+calibrate_current_0 = 0
+
+## calibrate_current_1			PA current ADC at 1 amp, integer
+# This is the ADC code returned for a PA current of one amp.
+# To see the ADC code being returned, enter zero for both current codes.
+# Linear interpolation is used to calculate the current.
+# Changes are immediate (no need to restart).
+calibrate_current_1 = 0
+
+## power_meter_calib_name		Power meter calibration, text choice
+# This is the calibration table used to convert the power sensor voltage measured by the ADC to the transmit power display.
+# It is a table of ADC codes and the corresponding measured power level.  If you have a power meter, you can create your own
+# table by selecting "New". Then enter ten or more power measurements from low to full power.
+# For the Hermes Lite2 version E3 filter board, use the built-in table "HL2FilterE3".
+# Changes are immediate (no need to restart).
+power_meter_calib_name = 'HL2FilterE3'
+
+
+################ Receivers SoapySDR, The SoapySDR interface to multiple SDRs.
 ## hardware_file_name		Hardware file path, rfile
 # This is the file that contains the control logic for each radio.
 #hardware_file_name = 'soapypkg/quisk_hardware.py'
@@ -602,7 +716,7 @@ Hermes_BandDictEnTx = False
 # Further items are present in the radio dictionary with names soapy_*
 
 
-################ Receivers SdrIQ, The SDR-IQ receiver by RfSpace
+################ Receivers SdrIQ, The SDR-IQ receiver by RfSpace.
 ## hardware_file_name		Hardware file path, rfile
 # This is the file that contains the control logic for each radio.
 hardware_file_name = 'quisk_hardware_sdriq.py'
@@ -633,7 +747,7 @@ sdriq_decimation = 1250
 
 
 
-################ Receivers Odyssey,   The Odyssey project using a UDP protocol similar to the HiQSDR
+################ Receivers Odyssey,   The Odyssey project.
 ## hardware_file_name		Hardware file path, rfile
 # This is the file that contains the control logic for each radio.
 #hardware_file_name = 'hiqsdr/quisk_hardware.py'
@@ -744,7 +858,7 @@ sndp_active = True
 #radio_sound_mic_boost = True
 
 
-################ Receivers Odyssey2,   The Odyssey-2 project using the HPSDR Hermes protocol
+################ Receivers Odyssey2,   The Odyssey-2 project.
 ## hardware_file_name		Hardware file path, rfile
 # This is the file that contains the control logic for each radio.
 #hardware_file_name = 'hermes/quisk_hardware.py'
@@ -759,7 +873,7 @@ sndp_active = True
 # You can set these options:
 
 ## use_rx_udp			Hardware type, integer choice
-# This is the type of UDP hardware.  Use 10 for the Hermes protocol.
+# This is the type of UDP hardware.  Use 10 for the Odyssey-2.
 #use_rx_udp = 10
 
 ## rx_udp_ip				IP change, text
@@ -828,7 +942,7 @@ Hermes_BandDictEnTx = False
 #Hermes_BandDictEnTx = True
 
 
-################ Receivers Afedri,   The Afedri SDR receiver with the Ethernet interface.
+################ Receivers Afedri,   The Afedri SDR receiver with Ethernet.
 ## hardware_file_name		Hardware file path, rfile
 # This is the file that contains the control logic for each radio.
 #hardware_file_name = 'afedrinet/quisk_hardware.py'
@@ -860,7 +974,7 @@ Hermes_BandDictEnTx = False
 #default_rf_gain = 11
 
 
-################ Receivers Control Head, Use Quisk to control a remote radio. No real hardware is used here.
+################ Receivers Control Head, Use Quisk to control a remote Quisk radio.
 ## hardware_file_name		Hardware file path, rfile
 # Quisk can be used as a control head to control a real radio located remotely.
 # This file contains the control logic for remote radios of type Hermes, SoftRock or HiQSDR.

setup.py

@@ -7,7 +7,7 @@ import os
 # You must define the version here.  A title string including
 # the version will be written to __init__.py and read by quisk.py.
 
-Version = '4.2.45'
+Version = '4.2.49'
 
 fp = open("__init__.py", "w")	# write title string
 fp.write("#Quisk version %s\n" % Version)