diff --git a/_quisk.pyd b/_quisk.pyd
new file mode 100644
index 0000000..3d38eaa
Binary files /dev/null and b/_quisk.pyd differ
diff --git a/microntrxpkg/__init__.py b/microntrxpkg/__init__.py
new file mode 100644
index 0000000..792d600
--- /dev/null
+++ b/microntrxpkg/__init__.py
@@ -0,0 +1 @@
+#
diff --git a/microntrxpkg/quisk_hardware.py b/microntrxpkg/quisk_hardware.py
new file mode 100644
index 0000000..73302a2
--- /dev/null
+++ b/microntrxpkg/quisk_hardware.py
@@ -0,0 +1,351 @@
+# This provides support for the SDR Micron TRX by David Fainitski, N7DDC
+
+import sys, wx, traceback, time
+from quisk_hardware_model import Hardware as BaseHardware
+
+DEBUG = 0	# print debug messages during operation
+WRITE_LOG = 1	# write the data received from the MicronTRX during self.log_time to the file self.log_name
+
+# https://github.com/Dfinitski/SDR-Micron
+
+# Control from PC to Micron TRX, 64 bytes, MSB first (big-endian)
+#
+# (0 - 7) Preamble, seven 0x55 and 0xD5
+# (8, 9, 10) "UCP"
+# (11) SN - Sequence Number 0 - 255
+# (12) RX0 enable, mode, 0 - off, 1 - 48kHz, 2 - 96kHz, 3 - 192kHz
+# (13) RX1 enable, mode, 0 - off, 1 - 48kHz, 2 - 96kHz, 3- 192kHz
+# (14) BS0 enable
+# (15) BS1 enable
+# (16) TX0 enable
+# (17) CDC enable
+# (18, 19, 20, 21) - 4 bytes RX0 frequency
+# (22, 23, 24, 25) - 4 bytes RX1 frequency
+# (26, 27, 28, 29) - 4 bytes BS0 frequency
+# (30, 31, 32, 33) - 4 bytes TX0 frequency
+# (34) - Attenuator, 0 - 31 (dB value)
+# (35) - BS0 Rate
+#          0 - 48 kHz, 
+#          1 - 96 kHz,
+#          2 - 192 kHz,
+#          3 - 384 kHz,
+#          4 - 768 kHz,
+#          5 - 1536 kHz
+#          6 - 1920 kHz
+# (36) LNA enable
+# (37) TX level 0 - 255
+# (38) Not used
+# (39) BS0 mode
+#         0 - 4096 buffered samples
+#         1 - 8192 buffered samples
+#         2 - 16384 buffered samples
+# (40) BS1 mode
+#         0 - 4096 buffered samples
+#         1 - 8192 buffered samples
+#         2 - 16384 buffered samples 
+# (41) BS0 period 50 - 255 ms (100ms is recommended)
+# (42) BS1 period 50 - 255 ms (100ms is recommended)
+# (43) Mic Boost, 0 - 1
+# (44) Not used
+# (45) PTT from PC
+# (46) CW mode 0 - 1
+# (47) CWX from PC - key manipulation
+# (48) Read only PWR, Output power in Watts
+# (49) Read only SWR x.x, from 1.0 to 9.9  as a natural number without decimal dot.
+# (50) Key Speed 10 - 63 ppm (20 by default)
+# (51) Paddle swap 0, 1
+# (52) Key mode, 0 = straight, 01 = Mode A, 10 = Mode B
+# (53) Key weight, 33 to 66, (50 by default)
+# (54) Key spacing, 0, 1
+# (55) ST Level, 0 - 255 sight tone level
+# (56) ST Freq MSB- 4 MSB bits
+# (57) ST Freq LSB - 8 LSB bits sight tone frequency in Hertz
+# (58) Delay ON, 8 - 255 ms (25 by default) - time for TX carrier delay is needed for transmitter preparing to TX
+# (59) Hang out time in tens ms 0 - 255 (0 to 2550 msec) (250 ms by default) needed to keep transmitter ready after PTT
+# (60) Not used
+# (61) Read only FW2 - firmware version MSB
+# (62) Read only FW1
+# (63) Read only FW0 - firmware version LSB
+
+# Define the name of the hardware and the items on the hardware screen (see quisk_conf_defaults.py):
+################ Receivers SdrMicronTRX, The SDR Micron TRX project by David Fainitski.
+## hardware_file_name		Hardware file path, rfile
+# This is the file that contains the control logic for each radio.
+#hardware_file_name = 'microntrxpkg/quisk_hardware.py'
+
+
+class Hardware(BaseHardware):
+  sample_rates =  [48]  #[48, 96, 192, 384, 768, 1536]
+  BS1_samples = {0:4096, 1:8192, 2:16384}
+  BS1_bytes = {0:4096 * 2, 1:8192 * 2, 2:16384 * 2}	# Two bytes per sample
+  def __init__(self, app, conf):
+    BaseHardware.__init__(self, app, conf)
+    self.usb = None
+    self.prefix = b'\x55\x55\x55\x55\x55\x55\x55\xD5'
+    self.read_data = bytearray()
+    self.rf_gain_labels = ('RF 0', 'RF -10', 'RF -20', 'RF -31')
+    self.index = 1
+    self.old_vfo = 0
+    self.sdrmicron_clock = 76800000
+    self.sdrmicron_decim = 1600
+    self.bscope_data = bytearray()
+    self.have_version = False
+    self.frame_msg = ''
+    self.remaining_BS1 = -1
+    self.log_name = "microntrx_log.dat"
+    self.log_time = 5.0		# seconds of log data
+    self.log_time0 = None	# starting time.time() to start log file
+    self.log_fp = None
+    self.pc_control = bytearray(64)
+    self.pc_control[0:8] = self.prefix
+    self.pc_control[8:11] = b'UCP'
+    self.pc_control[34] = 10	# Attenuator, 0 - 31 (dB value)
+    self.pc_control[35] = 0	# BS0 rate: 0:48ksps, 1:96, 2:192, 3:384, 4:768, 5:1536
+    self.pc_control[36] = 0	# LNA enable
+    self.pc_control[39] = 0	# Buffered BS0 samples, 0:4096, 1:8192, 2:16384
+    self.pc_control[40] = 0	# Buffered BS1 samples, 0:4096, 1:8192, 2:16384
+    self.pc_control[41] = 100	# BS0 period msec
+    self.pc_control[42] = 100	# BS1 period msec
+    self.pc_control[58] = 25	# time for TX carrier delay needed for transmitter preparing to TX, msec
+    self.pc_control[59] = 25	# tens of msec needed to keep transmitter ready
+    
+    if conf.fft_size_multiplier == 0:
+      conf.fft_size_multiplier = 3		# Set size needed by VarDecim
+
+  def open(self):	# This method must return a string showing whether the open succeeded or failed.
+    rx_bytes = 3	# rx_bytes is the number of bytes in each I or Q sample: 1, 2, 3, or 4
+    rx_endian = 1	# rx_endian is the order of bytes in the sample array: 0 == little endian; 1 == big endian
+    self.InitSamples(rx_bytes, rx_endian)	# Initialize: read samples from this hardware file and send them to Quisk
+    bs_bytes = 2
+    bs_endian = 1
+    self.InitBscope(bs_bytes, bs_endian, self.sdrmicron_clock, self.BS1_samples[self.pc_control[40]])	# Initialize bandscope
+    if sys.platform == 'win32':
+      return self.open_win()
+    return "This code is Windows only"
+
+  def open_win(self):
+    try:
+      import ftd2xx as d2xx
+    except:
+      return 'The ftd2xx module is missing'
+    enum = d2xx.createDeviceInfoList() # quantity of FTDI devices
+    if enum == 0:
+        return 'There are no FTDI devices available'
+    for i in range(enum):  # Searching and opening needed device
+      a = d2xx.getDeviceInfoDetail(i)
+      if DEBUG:
+        print ("%d: description %s, serial %s" % (i, a['description'], a['serial']))
+      if a['description']==b'SDR-Micron':
+        try:
+          self.usb = d2xx.openEx(a['serial'])
+        except:
+          return 'Device SDR-Micron could not be opened'
+        self.usb.setBitMode(255, 0)  # reset
+        time.sleep(0.1)
+        self.usb.setBitMode(255, 64)  # Configure FT2232H into Sync FIFO mode 
+        self.usb.setTimeouts(100, 100) # read, write
+        self.usb.setLatencyTimer(2)
+        self.usb.setUSBParameters(32, 32) # in_tx_size, out_tx_size
+        time.sleep(1.5) # waiting for device initialisation
+        self.usb.read(self.usb.getQueueStatus()) # clean the usb data buffer
+        self.frame_msg = a['description'].decode('utf-8') + '   S/N - ' + a['serial'].decode('utf-8')
+        return self.frame_msg
+    return 'Device SDR-Micron was not found'
+
+  def open_linux(self):		# Not finished
+    try:
+      import ftdi1 as d2xx
+    except:
+      return 'The ftdi1 module is missing'
+    self.usb = d2xx.new()
+    # Open Channel A (interface 1 in libftdi)
+    d2xx.set_interface(self.usb, d2xx.INTERFACE_A)
+    rc = d2xx.usb_open(self.usb, 0x0403, 0x6014) # 0x6014 is the standard FT232H PID
+    if rc == 0:
+      d2xx.usb_reset(self.usb)
+      d2xx.set_latency_timer(self.usb, 2)
+      # Enable Sync FIFO mode
+      # 0xFF = pin mask, 0x40 = BITMODE_SYNCFF
+      d2xx.set_bitmode(self.usb, 0xFF, d2xx.BITMODE_SYNCFF) 
+      if DEBUG:
+        print("Sync FIFO active via ftdi1.")
+      # To read at maximum speed, use d2xx.read_data()
+      d2xx.usb_close(self.usb)
+    d2xx.free(self.usb)
+
+  def close(self):
+    if self.usb:
+      self.usb.setBitMode(255, 0)  # reset
+      time.sleep(0.5)
+      self.usb.close()
+      self.usb = None
+    
+  def OnButtonRfGain(self, event):
+    btn = event.GetEventObject()
+    n = btn.index
+    if n == 0:
+      self.pc_control[34] = 0
+    elif n == 1:
+      self.pc_control[34] = 10
+    elif n == 2:
+      self.pc_control[34] = 20
+    elif n == 3:
+      self.pc_control[34] = 31
+    if DEBUG:
+      print ('pc_control[34]', self.pc_control[34])
+    self.rx_control_upd()
+
+  def ChangeFrequency(self, tx_freq, vfo, source='', band='', event=None):
+    if DEBUG:
+      print('ChangeFrequency tx_freq', tx_freq, 'vfo', vfo)
+    if tx_freq and tx_freq > 0:
+      tx_freq = int(tx_freq - self.transverter_offset)
+      self.pc_control[30] = self.pc_control[18] = (tx_freq >> 24) & 0xFF	# MSB
+      self.pc_control[31] = self.pc_control[19] = (tx_freq >> 16) & 0xFF
+      self.pc_control[32] = self.pc_control[20] = (tx_freq >>  8) & 0xFF
+      self.pc_control[33] = self.pc_control[21] = (tx_freq      ) & 0xFF	#LSB
+      self.rx_control_upd()
+    if vfo:
+      vfo =  int(vfo - self.transverter_offset)
+      if vfo != self.old_vfo:
+        self.old_vfo = vfo
+        self.pc_control[26] = (vfo >> 24) & 0xFF	# MSB
+        self.pc_control[27] = (vfo >> 16) & 0xFF
+        self.pc_control[28] = (vfo >>  8) & 0xFF
+        self.pc_control[29] = (vfo      ) & 0xFF	#LSB
+        self.rx_control_upd()
+    return tx_freq, vfo
+  
+  def VarDecimGetChoices(self): # Return a list/tuple of strings for the decimation control.
+    return list(map(str, self.sample_rates)) # convert integer to string
+
+  def VarDecimGetLabel(self):		# return a text label for the control
+    return "Sample rate ksps"
+  
+  def VarDecimGetIndex(self):		# return the current index
+    return self.index
+  
+  def VarDecimSet(self, index=None): # return sample rate
+    if index is None: # initial call to set the sample rate before the call to open()
+      rate = self.application.vardecim_set
+      try:
+        self.index = self.sample_rates.index(rate // 1000)
+      except:
+        self.index = 0
+    else:
+      self.index = index
+    self.pc_control[35] = self.index
+    rate = self.sample_rates[self.index] * 1000
+    if DEBUG:
+      print("varDecimSet index", self.index, "rate", rate)
+    self.rx_control_upd()
+    return rate
+  
+  def VarDecimRange(self):  # Return the lowest and highest sample rate.
+    #return (48000, 1536000)
+    return (48000, 48000)
+
+  def StartSamples(self):	# called by the sound thread
+    self.pc_control[12] = 1	# RX0 enable
+    self.pc_control[15] = 1	# BS1 enable
+    self.rx_control_upd()
+    if WRITE_LOG:
+      if self.log_fp is None:
+        self.log_fp = open(self.log_name, "wb")
+  
+  def StopSamples(self):	# called by the sound thread
+    self.pc_control[12] = 0
+    self.pc_control[15] = 0
+    self.rx_control_upd()
+
+  def rx_control_upd(self):
+    if self.usb:
+      try:
+        self.usb.write(self.pc_control)
+      except:
+        print('Error while rx_control_upd')  
+    if self.pc_control[11] < 255:	# sequence number
+      self.pc_control[11] += 1
+    else:
+      self.pc_control[11] = 0
+
+  def GetRxSamples(self):	# Read from the MicronTRX. Called frequently from the sound thread.
+    if not self.usb:
+      return
+    count = self.usb.getQueueStatus()	# Read all available bytes
+    if count > 0:
+      data = bytearray(self.usb.read(count))
+      self.read_data += data
+      if WRITE_LOG:
+        if self.log_fp:
+          if self.log_time0 is None:
+            self.log_time0 = time.time()
+          if time.time() - self.log_time0 < self.log_time:
+            self.log_fp.write(data)
+          else:
+            self.log_fp.close()
+            self.log_fp = None
+    while True:
+      start = self.read_data.find(self.prefix)
+      if start < 0:	# No prefix
+        return
+      if start > 0:
+        del self.read_data[0:start]
+        if DEBUG:
+          print ("USB blocks lost sync")
+      if len(self.read_data) < 11:
+        return
+      block_type = self.read_data[8:11]
+      if block_type == b'BS0':
+        if len(self.read_data) < 508:
+          return
+        del self.read_data[0:508]
+      elif block_type == b'BS1':
+        if len(self.read_data) < 508:
+          return
+        packet_number = self.read_data[12]
+        if packet_number == 0:			# start of a block of data
+          self.remaining_BS1 = self.BS1_bytes[self.pc_control[40]]
+          self.bscope_data = self.read_data[16:508]		# 492 bytes
+          self.remaining_BS1 -= 492
+        elif self.remaining_BS1 >= 492:
+          self.bscope_data += self.read_data[16:508]		# 492 bytes
+          self.remaining_BS1 -= 492
+        elif self.remaining_BS1 <= 0:
+          pass
+        else:
+          self.bscope_data += self.read_data[16:self.remaining_BS1 + 16]  
+          self.remaining_BS1 = -1
+          # self.AddBscopeSamples(self.bscope_data)
+        del self.read_data[0:508]
+      elif block_type == b'CDM':
+        if len(self.read_data) < 180:
+          return
+        del self.read_data[0:180]
+      elif block_type == b'RX0':
+        if len(self.read_data) < 508:
+          return
+        if self.read_data[12]:
+          self.GotClip()
+        self.AddRxSamples(self.read_data[16:508])
+        del self.read_data[0:508]
+      elif block_type == b'RX1':
+        if len(self.read_data) < 508:
+          return
+        del self.read_data[0:508]
+      elif block_type == b'SBL':
+        if len(self.read_data) < 32:
+          return
+        del self.read_data[0:32]
+      elif block_type == b'UCP':
+        if len(self.read_data) < 64:
+          return
+        if self.have_version is False:
+          self.have_version = True
+          self.frame_msg += '   F/W version - %d.%d' % (self.read_data[61], self.read_data[63])
+          self.application.main_frame.SetConfigText(self.frame_msg)
+        del self.read_data[0:64]
+      else:
+        del self.read_data[0:8]
+        if DEBUG:
+          print("Unknown USB block type")